What did you do to your 924/944 today
#4802
Instructor
Just realized the first pic is without the mounting screws so you can see the 3m tape a little here it is with the mounting screws in. Also here is the link to just the front. I bought the whole kit all around I plan on doing my sideskirts after I get my mudflaps in. The spare stuff I plan on giving to my brother in law for his car.
http://www.ebay.com/itm/ALL-FIT-UNIV...item2c64dcd357
http://www.ebay.com/itm/ALL-FIT-UNIV...item2c64dcd357
#4805
Added a Computer to my car, the screen takes the place of the dash speaker vent, and the pc is mounted under the passenger side of the dash. I plan on remaking the screen mount, it came out too puffy. Attachment 701708
Last edited by GGX2; 07-07-2014 at 06:14 PM.
#4806
Instructor
Fitted new throttle position switch and throttle body reseal kit. Very fiddly job but worth it. The WOT contact in the TPS was broken and it was full of oil when I opened it up. Idles much better now.
#4807
Today I got
My Custom Title
Rennlist Member
My Custom Title
Rennlist Member
Added a Computer to my car, the screen takes the place of the dash speaker vent, and the pc is mounted under the passenger side of the dash. I plan on remaking the screen mount, it came out too puffy. Attachment 701708
#4809
Three Wheelin'
Join Date: Jan 2010
Location: Durham Region/GTA East, Canada
Posts: 1,380
Likes: 0
Received 1 Like
on
1 Post
Replaced the cut rad hose. Filled it up, and took it for a spin. So far so good. I'll have to watch it to see if it gets air locked. I drove it with the heat on full for 15 min and it never climbed more than a fraction above the first mark, which is normally where it sits once it is warmed up. I read Clarks garage on bleeding the system, so I'll give it a go tomorrow after going for another spin if the guage gives me any wierd readings.
BTW the snow storm was pretty bad. I had more than 30cm on my driveway....the street had even bigger drifts..don't think the 944 would have made it out of my street yesturday.
BTW the snow storm was pretty bad. I had more than 30cm on my driveway....the street had even bigger drifts..don't think the 944 would have made it out of my street yesturday.
#4810
Rainman
Rennlist Member
Rennlist Member
installed this monster.
to accomodate my relocated alternator i had to shorten the lower radiator hose, in turn causing the passenger side fan to rub it. car runs very hot with only one fan. had been planning on a large single fan for some time, came upon this one for a great price. first "run", you can feel the air being pulled from in front of the bumper, through 2 oil coolers, a 3" intercooler, an ac condenser and the radiator. nice.
to accomodate my relocated alternator i had to shorten the lower radiator hose, in turn causing the passenger side fan to rub it. car runs very hot with only one fan. had been planning on a large single fan for some time, came upon this one for a great price. first "run", you can feel the air being pulled from in front of the bumper, through 2 oil coolers, a 3" intercooler, an ac condenser and the radiator. nice.
#4812
Rainman
Rennlist Member
Rennlist Member
I had originally planned on the Ford Taurus fan and actually made a fiberglass shroud for it, but it was a bit too tight for my taste (very close to the PS pulley, I think my radiator is closer to the engine than factory due to my custom front body structure) so I went for this. I might throw it up for sale if someone wanted to try it out.
Last edited by V2Rocket; 02-11-2013 at 02:26 PM.
#4813
Instructor
Ordered a list of parts. PS rack seal kit, heater control valve, intake manifold gaskets, throttle body seal ring, AFM gasket, upper and lower oil filler tube seals, hood shocks and rebuilt ICV from 944 OL. Now I just have to wait for the order to get to my house. Giddy like a kid. Will also be sending my injectors to Witch Hunter and have them cleaned and rebuilt. Cant wait
Last edited by A.M.H; 02-13-2013 at 08:23 AM.
#4814
Three Wheelin'