What did you do to your 924/944 today
#3991
Instructor
Hooked up oil pressure sending unit. PO only connected with rubber boots, no actual hard wire connections!
Repaired headlight movement shaft. PO had lost washer and circlip on drivers side.
Replace interior lighting fuse. Shorted it out pulling console and DME out to do resolder job...
Put summer tires on. PO had winters on 968 rims... Now phone dials with Continental Extreme Contacts
Repaired headlight movement shaft. PO had lost washer and circlip on drivers side.
Replace interior lighting fuse. Shorted it out pulling console and DME out to do resolder job...
Put summer tires on. PO had winters on 968 rims... Now phone dials with Continental Extreme Contacts
#3992
Today I got
My Custom Title
Rennlist Member
My Custom Title
Rennlist Member
#3997
Late Porkchops
Rennlist Member
Rennlist Member
^^^^ Looks good.
I polished like a mad man on mine last week and entered a local car show with my buddy. There were about 50 classes - and 2 import classes. Pre 1980 and post 1980.
He got 2nd in the pre1980 and I got 2nd in the post 1980. Not sour grapes at all but the cars that won our respective classese should not have. The car that beat me was just an off the show room regular BMW from 2011. Ok it did not have any paint chips LOL I am not saying I was deserving of first but that is kind of lame. Now if a Ferarri or something there then Ok LOL LOL.
I polished like a mad man on mine last week and entered a local car show with my buddy. There were about 50 classes - and 2 import classes. Pre 1980 and post 1980.
He got 2nd in the pre1980 and I got 2nd in the post 1980. Not sour grapes at all but the cars that won our respective classese should not have. The car that beat me was just an off the show room regular BMW from 2011. Ok it did not have any paint chips LOL I am not saying I was deserving of first but that is kind of lame. Now if a Ferarri or something there then Ok LOL LOL.
#3999
Today I got
My Custom Title
Rennlist Member
My Custom Title
Rennlist Member
Dropped her off at Big-O for a front suspension alignment (hasn't seen a mechanic in months, and I don't like trusting people with her )
Told them to do 1/16" toe-in, and 3° caster, as 924.org said, along with -2° camber. Does this sound ok?????
Told them to do 1/16" toe-in, and 3° caster, as 924.org said, along with -2° camber. Does this sound ok?????
#4000
Setting-wise that sounds ok, although zeroing the toe is more typical to save on tyres.
Did you know that they'll need a special tool to properly set the toe and camber at the rear? Without it I think it would be a tricky job.
Let me know how they get on, because this is something that's on my mind too - I recently lowered the rear on the eccentrics, and maxed the camber adjusters in front. Hope to take into a place and get it measured, so I can decide what to do next.
I'd trust an every-day mech to get the front right as it's really simple - but the rear set up is a tricky job.
Did you know that they'll need a special tool to properly set the toe and camber at the rear? Without it I think it would be a tricky job.
Let me know how they get on, because this is something that's on my mind too - I recently lowered the rear on the eccentrics, and maxed the camber adjusters in front. Hope to take into a place and get it measured, so I can decide what to do next.
I'd trust an every-day mech to get the front right as it's really simple - but the rear set up is a tricky job.
#4001
Track Day
Join Date: Apr 2012
Location: Massachusetts
Posts: 17
Likes: 0
Received 0 Likes
on
0 Posts
88944 restoration
sent 16 inch phone dials to be blasted silver powder coated car is down to bare metal zermatt silver w/xtra metal flake w/clear coat .Hope to be show ready for summer
#4003
Today I got
My Custom Title
Rennlist Member
My Custom Title
Rennlist Member
Setting-wise that sounds ok, although zeroing the toe is more typical to save on tyres.
Did you know that they'll need a special tool to properly set the toe and camber at the rear? Without it I think it would be a tricky job.
Let me know how they get on, because this is something that's on my mind too - I recently lowered the rear on the eccentrics, and maxed the camber adjusters in front. Hope to take into a place and get it measured, so I can decide what to do next.
I'd trust an every-day mech to get the front right as it's really simple - but the rear set up is a tricky job.
Did you know that they'll need a special tool to properly set the toe and camber at the rear? Without it I think it would be a tricky job.
Let me know how they get on, because this is something that's on my mind too - I recently lowered the rear on the eccentrics, and maxed the camber adjusters in front. Hope to take into a place and get it measured, so I can decide what to do next.
I'd trust an every-day mech to get the front right as it's really simple - but the rear set up is a tricky job.
ALSO, picked up my new twists from HICKS (thanks Chris!! ) They look amazing! More pics will be in my project thread.
#4005
Freedom Enthusiast
Rennlist Member
Rennlist Member
Butters, Dyno-comp on Raintree can do alignment on our cars. The owner races a 700hp Subaru STI but one of his favorite cars is the 944 Turbo. Dyno-comp did the alignment on my car and put it up on the dyno for the 323rwhp run after the rebuild last year.