So what did you do to your 928 Today......
#511
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Installed the battery in the Jalapeno and started it. Started right up. I let it warm up, cleaned the windows and drove it around the block (2 miles). I started the '89 and let it warm up and took it around the block also. I am replacing the brake lines on the GTS with stainless steel braided lines, so I started with the left rear, which I think is the hardest one to replace.
#512
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Stripped down the Bilstiens/stock springs I bought from GregBBRD from his "virgin 90 part out", getting ready to blast clean and repaint. Got my list organized for the big push to finish the suspension install, get the brakes cleaned and rebuilt, and the details remaining underneath so it can get off the blocks onto the ground again!
#513
Rennlist Member
#514
Rennlist Member
#515
Racer
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Took apart the fuel pressure and return lines, now to just clean the fittings and install the new hose.
#516
Chronic Tool Dropper
Lifetime Rennlist
Member
Lifetime Rennlist
Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
after the rains this past weekend/week, it was nice enough today to use it for a few errands. Needed some parts for my upgraded brake flush unit. Back home, washed it. But that caused more rain.
Last edited by dr bob; 03-25-2011 at 12:15 PM.
#519
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Did a brake system flush/fill today with ATE Super Blue fluid (Dot 4) and swapped out pads with more aggressive Mintex F4 compound semi-metallics.
Gettin' her in shape for SITM!
Gettin' her in shape for SITM!
Last edited by White Lightnin'; 04-02-2011 at 04:57 PM. Reason: added pic
#520
Three Wheelin'
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Took my baby out for a "touchless" car wash just to get the grime / dust off... Discovered I'm gonna need to "adjust" driver side door and/or buy a new gasket... it likes to leak a little air / water. Oh well, things could be MUCH worse and she looks GORGEOUS!!!
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#521
Chronic Tool Dropper
Lifetime Rennlist
Member
Lifetime Rennlist
Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Weather looking dodgy, so I though I'd sneak out and do at least the cam-cover portion of the top-of-engine refresh. Started by pulling out the Big Box of Parts I got 18 months or so ago for the project. Found things I didn't expect (a Good Thing) and also didn't find some WYAIT stuff I now know I'll need. So the original cam covers are still on the engine. Parts order going out for those last bits.
This is an appearance-only refresh. The car runs so darn well I kinda hate to mess with it.
------
Noted the odo this morning during a quick hardware-store run: 99986! In the next day or so, my baby will transition out of "low miles" status and into whatever the next stage is. Just last year it was old enough to drink, and now this! Oh, the heartbreaks...
This is an appearance-only refresh. The car runs so darn well I kinda hate to mess with it.
------
Noted the odo this morning during a quick hardware-store run: 99986! In the next day or so, my baby will transition out of "low miles" status and into whatever the next stage is. Just last year it was old enough to drink, and now this! Oh, the heartbreaks...
#522
In Your Face, Ace
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Just had the rising RRFPR rebuilt and putting it back on the car. Can't wait to hear the turbo spool up and the waste gate suddering!!!!!!!!!!
#523
Burning Brakes
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Finally got my PKlutch installed... ![burnout](https://rennlist.com/forums/graemlins/burnout.gif)
But while I was under there, I noticed that the master cylinder for the clutch is leaking!![ooops](https://rennlist.com/forums/graemlins/icon501.gif)
Just a little now... But that means I've got a rough spot ahead...
![burnout](https://rennlist.com/forums/graemlins/burnout.gif)
But while I was under there, I noticed that the master cylinder for the clutch is leaking!
![ooops](https://rennlist.com/forums/graemlins/icon501.gif)
Just a little now... But that means I've got a rough spot ahead...
#524
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Weather looking dodgy, so I though I'd sneak out and do at least the cam-cover portion of the top-of-engine refresh. Started by pulling out the Big Box of Parts I got 18 months or so ago for the project. Found things I didn't expect (a Good Thing) and also didn't find some WYAIT stuff I now know I'll need. So the original cam covers are still on the engine. Parts order going out for those last bits.
This is an appearance-only refresh. The car runs so darn well I kinda hate to mess with it.
------
Noted the odo this morning during a quick hardware-store run: 99986! In the next day or so, my baby will transition out of "low miles" status and into whatever the next stage is. Just last year it was old enough to drink, and now this! Oh, the heartbreaks...
This is an appearance-only refresh. The car runs so darn well I kinda hate to mess with it.
------
Noted the odo this morning during a quick hardware-store run: 99986! In the next day or so, my baby will transition out of "low miles" status and into whatever the next stage is. Just last year it was old enough to drink, and now this! Oh, the heartbreaks...
Your baby is ready to run! Enjoy!
#525
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
So I found the iPhone app
For rennlist and now there will be way mote pics if this works. You can attach the pix right here instead of a separate upload.
For rennlist and now there will be way mote pics if this works. You can attach the pix right here instead of a separate upload.