The 133,333 mile engine rebuild thread
#466
Rennlist Member
Yes, it's done. I'm not sure what the noise that it makes is supposed be though.
https://www.youtube.com/watch?v=umnpH0gV4z0
https://www.youtube.com/watch?v=umnpH0gV4z0
#467
Rennlist Member
#469
Just a car guy
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2002
Location: South Lyon, Michigan, Ewe Ess Eh
Posts: 9,927
Received 835 Likes
on
524 Posts
Game on.
Got a package from Arizona Gary. Cut the rod in two pieces and disassembled the variocam, chain and cams.
Cleaned a few parts, including the variocam assembly in a bag of oil.
Got a package from Arizona Gary. Cut the rod in two pieces and disassembled the variocam, chain and cams.
Cleaned a few parts, including the variocam assembly in a bag of oil.
The following users liked this post:
yaz996 (04-20-2020)
#470
Just a car guy
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2002
Location: South Lyon, Michigan, Ewe Ess Eh
Posts: 9,927
Received 835 Likes
on
524 Posts
Getting ready for tomorrow. Since I am working from home, right now, I have an additional one and a half hours to work on my stuff. Things should fall together nicely over the next couple of days.
The following users liked this post:
Porschetech3 (04-20-2020)
#471
Didn't want to brag prematurely but Arizona always beats Taxachusetts
#473
Rennlist Member
Yes, it's done. I'm not sure what the noise that it makes is supposed be though.
https://www.youtube.com/watch?v=umnpH0gV4z0
https://www.youtube.com/watch?v=umnpH0gV4z0
#474
#475
Just a car guy
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2002
Location: South Lyon, Michigan, Ewe Ess Eh
Posts: 9,927
Received 835 Likes
on
524 Posts
Probably needs Driven break-in oil. I might have some left over after my build.
Speaking of which, I completed most of the bank #1 cam install today.
Put a bag over it so dirt would be less likely to find the grease. I ran out of steam before I could complete the cam cover installation.
It's clear bank #1 tensioner pads are newer than bank #2. This is consistent with the cam deviation numbers I saw before the engine needed to come apart.
Bank #2 cams ready for lube and installation into the head. Should be able to tackle that tomorrow. Might even be able to seal up the two cam covers, if I don't get worn out from a hard day of Webex meetings.
Speaking of which, I completed most of the bank #1 cam install today.
Put a bag over it so dirt would be less likely to find the grease. I ran out of steam before I could complete the cam cover installation.
It's clear bank #1 tensioner pads are newer than bank #2. This is consistent with the cam deviation numbers I saw before the engine needed to come apart.
Bank #2 cams ready for lube and installation into the head. Should be able to tackle that tomorrow. Might even be able to seal up the two cam covers, if I don't get worn out from a hard day of Webex meetings.
The following users liked this post:
yaz996 (04-21-2020)
#476
Rennlist Member
Nice work Scott, you're moving along quickly!
#477
Just a car guy
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Jan 2002
Location: South Lyon, Michigan, Ewe Ess Eh
Posts: 9,927
Received 835 Likes
on
524 Posts
Thanks Bill. I wasn't in the groove today. Kind of pissy. Little things would irritate me, and constantly having oil and grease on my hands made it even worse. Had to stop before I did something extra stupid.
It's coming along. Just need to remain focused and take things slow. Have the next steps cued up on the DVD to duplicate what I did on bank #1 today, so I can do the same on bank #2 tomorrow.
It's coming along. Just need to remain focused and take things slow. Have the next steps cued up on the DVD to duplicate what I did on bank #1 today, so I can do the same on bank #2 tomorrow.
#478
Rennlist Member
My kit was missing the Drei Bond. All the oil leaked out.
The following 3 users liked this post by Scott at Team Harco:
The following 2 users liked this post by Scott at Team Harco:
latonnelier (04-23-2020),
yaz996 (04-23-2020)