What did you do to your 997 today?
The following 5 users liked this post by acollen:
Amrit.boxer (10-01-2023),
anewman (10-01-2023),
cjarrett (10-01-2023),
EVOMMM (10-01-2023),
Graufuchs (10-01-2023)
The following 11 users liked this post by Fatsix:
Dubber (10-02-2023),
Graufuchs (10-01-2023),
Kechu (10-02-2023),
Liste-Renn (10-02-2023),
Ob917 (10-05-2023),
and 6 others liked this post.
Rennlist Member
Drove a section of the PCH, much fun, and took this pic as the sun set.
No editing- this is all natural light.
"Golden hour" can cast a magical glow.
My rotors are like mirrors.
No editing- this is all natural light.
"Golden hour" can cast a magical glow.
My rotors are like mirrors.
Last edited by Liste-Renn; 10-02-2023 at 12:50 PM.
The following 5 users liked this post by Liste-Renn:
anewman (10-07-2023),
jbkusa (10-02-2023),
Prairiedawg (10-02-2023),
Rig.Stunts (10-02-2023),
VT Blue (10-02-2023)
The following 4 users liked this post by WhatTheFetch:
ATX_Native (10-02-2023),
Dubber (10-02-2023),
Ohio Performance (10-02-2023),
TerrestrialFlyte (10-03-2023)
Racer
Just saw this on my shops site.
Now I'm at 112k miles, so I'm installing a new water pump, low temp thermostat, new drive belts, full suspension refresh, new CV boots, painting brake calipers, topping up the A/C, new CUP lip, fixing some interior bits and new wheels also being put on.
I should have it back this week! Can't wait!
Last edited by Bwoy1981; 10-02-2023 at 03:52 PM.
The following 4 users liked this post by Bwoy1981:
Rennlist Member
The following users liked this post:
joes c4 cab (10-03-2023)
The following 3 users liked this post by GT3twenty10:
Rennlist Member
The following 5 users liked this post by WhatTheFetch:
Dubber (10-03-2023),
EVOMMM (10-03-2023),
Graufuchs (10-03-2023),
misterdega (10-03-2023),
VT Blue (10-05-2023)
Rennlist Member
Rennlist Member
Finished the clutch job.
- New OEM Sachs clutch & throwout bearing
- Machined flywheel
- Clutch bleed with Motive Power Bleeder
- New OEM engine mounts (964RS still a little too stiff, will probably fill the OEM mounts with more material at some point)
- Oil change
- Center radiator install and coolant burp (did coolant not long ago)
Drives like a dream, best its run since owning it (5 years now).
- New OEM Sachs clutch & throwout bearing
- Machined flywheel
- Clutch bleed with Motive Power Bleeder
- New OEM engine mounts (964RS still a little too stiff, will probably fill the OEM mounts with more material at some point)
- Oil change
- Center radiator install and coolant burp (did coolant not long ago)
Drives like a dream, best its run since owning it (5 years now).
The following 5 users liked this post by cjarrett:
Dubber (10-05-2023),
Graufuchs (10-03-2023),
Rig.Stunts (10-03-2023),
TerrestrialFlyte (10-03-2023),
VT Blue (10-05-2023)
Rennlist Member
view from front wheel, prepping for weekend car show.
Rennlist Member
Got my calipers redone and my wheels freshly painted and powder coated clear silver. All ceramic coated.
The following 11 users liked this post by misterdega:
anewman (10-05-2023),
Bwoy1981 (10-05-2023),
cjarrett (10-04-2023),
EVOMMM (10-05-2023),
frederickcook87 (10-17-2023),
and 6 others liked this post.
The following 6 users liked this post by WhatTheFetch:
anewman (10-07-2023),
Dubber (10-05-2023),
EVOMMM (10-05-2023),
MauritsK (10-05-2023),
misterdega (10-08-2023),
and 1 others liked this post.
Rennlist Member
The following 3 users liked this post by WhatTheFetch: