What did you do to your 996TT today?
RL Community Team
Rennlist Member
Rennlist Member
So, a little bit of a set back...
When I was speaking with Marek (Markski) the other day, he advised that the the installation of his bendable intake, if the engine remained in the car throughout, would require that the factory intake would have to be cut out in order to be removed. Well, I lifted the car up today and can confirm there is no way to remove the OEM intake in one piece without removing the engine from the car. I am not prepared to butcher the factory intake through this process, so the engine will need to be dropped (again) in order to facilitate the installation of the 980s.
As I did not plan on another engine drop this season, the 980s will not go on until next season.
A bit of a **** off, but I do want to keep all the factory pieces intact, so not a lot that can be done here.
But, I have a question....
Even though Kline (and Sam) were kind enough to produce a 90mm cat piece for the 980s, can I still install the Kline with the 90mm hot pipe, even if the OEM turbos will require a 75mm pipe? I really want to make at least a little progress this year, so the installation of the Kline will bring a little happiness. The flanges look identical, save for a 15mm id difference - going the other way will most certainly introduce surge, but can I get away with using a 90mm turbo flange on the K24s without issue?
Cheers,
When I was speaking with Marek (Markski) the other day, he advised that the the installation of his bendable intake, if the engine remained in the car throughout, would require that the factory intake would have to be cut out in order to be removed. Well, I lifted the car up today and can confirm there is no way to remove the OEM intake in one piece without removing the engine from the car. I am not prepared to butcher the factory intake through this process, so the engine will need to be dropped (again) in order to facilitate the installation of the 980s.
As I did not plan on another engine drop this season, the 980s will not go on until next season.
A bit of a **** off, but I do want to keep all the factory pieces intact, so not a lot that can be done here.
But, I have a question....
Even though Kline (and Sam) were kind enough to produce a 90mm cat piece for the 980s, can I still install the Kline with the 90mm hot pipe, even if the OEM turbos will require a 75mm pipe? I really want to make at least a little progress this year, so the installation of the Kline will bring a little happiness. The flanges look identical, save for a 15mm id difference - going the other way will most certainly introduce surge, but can I get away with using a 90mm turbo flange on the K24s without issue?
Cheers,
I've got my buddy's '2 with Tial 1000's and Markski softpipes on the hoist right now if you have any questions about it...maybe can make it all work..
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Let me see if I have any extra factory intake so you can just cut yours out. But I do agree you can just use the original for now and we can take it easy so we don’t put too much strain on the system until. As for the exhaust, you can absolutely install it. No problem at all.
hey 993Gat! Been a while I hope you’re well. That’s really cool of you to offer.
hey 993Gat! Been a while I hope you’re well. That’s really cool of you to offer.
__________________
Proud TOP Porsche Distributor For:
Kline-Innovation - ams Performance - TiALSPORT/XONA - #1 COBB PRO TUNER - CSF - IPD Plenums - DO88 - dodsonmotorsport
310-600-1850 - sam@bydesignauto.com
Proud TOP Porsche Distributor For:
Kline-Innovation - ams Performance - TiALSPORT/XONA - #1 COBB PRO TUNER - CSF - IPD Plenums - DO88 - dodsonmotorsport
310-600-1850 - sam@bydesignauto.com
RL Community Team
Rennlist Member
Rennlist Member
RL Community Team
Rennlist Member
Rennlist Member
RL Community Team
Rennlist Member
Rennlist Member
Let me see if I have any extra factory intake so you can just cut yours out. But I do agree you can just use the original for now and we can take it easy so we don’t put too much strain on the system until. As for the exhaust, you can absolutely install it. No problem at all.
hey 993Gat! Been a while I hope you’re well. That’s really cool of you to offer.
hey 993Gat! Been a while I hope you’re well. That’s really cool of you to offer.
Happy that the exhaust will work with the K24s, that may be enough to carry me over...
You can run the 980s with the OEM intake. Just have Sam give you a lower HP map, maybe 1.0 bar. No problem at all. You will have an intake restriction but that won't hurt anything at 500-550whp.
RL Community Team
Rennlist Member
Rennlist Member
Thanks for chiming in John, will the turbos be running efficiently at that pressure?
RL Community Team
Rennlist Member
Rennlist Member
Ok, we are back on then!
The following users liked this post:
T2 (03-12-2023)
BTW, cutting out the OEM pipes with the engine lowers 3" is very simple. The OEM pipes are worthless. For anyone moderately handy with these cars, it's an easy DIY.
Last edited by powdrhound; 03-12-2023 at 03:14 PM.
RL Community Team
Rennlist Member
Rennlist Member
Efficiency is a relative term. How efficient do you wanna be? If you are seeking max efficiency you would also need to significantly open up the exhaust. For street use, none of this really matters for the most part especially at moderate 550-600whp levels.
BTW, cutting out the OEM pipes with the engine lowers 3" is very simple. The OEM pipes are worthless. For anyone moderately handy with these cars, it's an easy DIY.
BTW, cutting out the OEM pipes with the engine lowers 3" is very simple. The OEM pipes are worthless. For anyone moderately handy with these cars, it's an easy DIY.
I keep all the parts I remove from the car, I just don't want to chop anything up.
RL Community Team
Rennlist Member
Rennlist Member
In other news...
Cannot, for the life of me, figure this out... I cut all the sensors off and soldered the ends together, finished it up with some heat shrink.
Porsche Sorcery, I say...
Cannot, for the life of me, figure this out... I cut all the sensors off and soldered the ends together, finished it up with some heat shrink.
Porsche Sorcery, I say...
RL Community Team
Rennlist Member
Rennlist Member
You have an open circuit somewhere.