UMW STG3A ZC Breaks New Ground: Dyno Sheet
#61
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Geoffrey per our conversation, the outcome would have been different is you had a little more boost on the top end.
Jean, the Germans won't give out compressor maps..
And if you do your research the Brits don't either..
Jean, the Germans won't give out compressor maps..
And if you do your research the Brits don't either..
#63
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Thanks Kevin, I thought I knew that but was just wondering if Geoffrey had better info.
I am not sure if you mean that you have them but you don't wish to share them or you don't have them.
Just to clarify, I am not looking for them, I do have the Audi K26 compressor maps that most people have too.
What is your point of view of why the compressor efficency is falling off beyond 1.2-1.3 Bar? K26 should be able to flow beyond those levels.
Originally Posted by Geoffrey
Jean, I don't have anything I'm willing to give out.
![Confused](https://rennlist.com/forums/images/smilies/confused.gif)
What is your point of view of why the compressor efficency is falling off beyond 1.2-1.3 Bar? K26 should be able to flow beyond those levels.
#64
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by Geoffrey
Hi Kevin, Would you also post the boost graph that accompanies this run? I finished the GT3R tt project and found that the K24/26 turbos from Germany would not hold 1.3bar of boost. By 4750 they were falling off, at 6000rpm they were down to 1bar and down to .9bar at 8000rpm. I think that if they were able to stay on their efficency island of the compressor map, I'd see another 50-70hp with reduced intake air temps.
#65
Nordschleife Master
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
"What is your point of view of why the compressor efficency is falling off beyond 1.2-1.3 Bar? K26 should be able to flow beyond those levels."
The compressor cannot keep up with the airflow requirements of the engine, especially running it to 8000rpm. I was hoping the turbos would maintain boost to 7000rpm, but expected them to fall off towards 8000rpm. They just don't flow enough air, the wastegates are completely closed, I checked while running on the dyno.
The compressor cannot keep up with the airflow requirements of the engine, especially running it to 8000rpm. I was hoping the turbos would maintain boost to 7000rpm, but expected them to fall off towards 8000rpm. They just don't flow enough air, the wastegates are completely closed, I checked while running on the dyno.
#66
Nordschleife Master
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Bob, This was not a stock internal 996tt engine, but rather a 996 Race engine modified for turbos so the airflow comparison will be much different than the small port, small valve, large combustion chamber, small camshaft, small header found in the stock 996tt engine.
#67
Pro
Thread Starter
Join Date: Aug 2005
Location: Michigan
Posts: 726
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Just wanted to show some pics of the new hardware that is filtering in for the engine build...Here is my new GT3RS crank...with the correct engine upgrades this will spin to 9K.... Also, Kevin has been working hard with the head R+D and has finalized the details of the head and has produced some prelim flow numbers. He tested our revalved head against the Porsche RSR head and so far we are outflowing Porsche's best...
Exhaust Flow CFM
TT Head...............244
RSR Head.. ...........260
UMW Head............302
These heads are going to have custom made Titanium intake valves and Inconel exhaust valves rated for 2100degrees F. He has put into production an order for 250 valves just to get started...The intake numbers are excellent as well. I think these heads with these flow numbers and hardware will make a potent and efficient setup.All in all, the project is progressing well....More later...Kevin
Exhaust Flow CFM
TT Head...............244
RSR Head.. ...........260
UMW Head............302
These heads are going to have custom made Titanium intake valves and Inconel exhaust valves rated for 2100degrees F. He has put into production an order for 250 valves just to get started...The intake numbers are excellent as well. I think these heads with these flow numbers and hardware will make a potent and efficient setup.All in all, the project is progressing well....More later...Kevin
#68
Pro
Thread Starter
Join Date: Aug 2005
Location: Michigan
Posts: 726
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Here are some pics of the cases that just came back....Kevin is finishing up some oiling mods and some final detail work. The rotating assembly is being balanced from front crank pulley to the pressure plate and everything in between...individually clearanced Porsche Motorsports bearing to specific bearing journals.... details..details.. Kevin
#70
Pro
Thread Starter
Join Date: Aug 2005
Location: Michigan
Posts: 726
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by wross996tt
Nice...Kevin, that looks ...SPECIAL...can't wait to see what happens next.
#73
Pro
Thread Starter
Join Date: Aug 2005
Location: Michigan
Posts: 726
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by markski
Nice Kevin....
BTW, when u get ur car back u might have to change ur plates to stage 5 LOL
BTW, when u get ur car back u might have to change ur plates to stage 5 LOL