What did you do to your 924/944 today
10-07-2012, 09:25 PM
#4441
Addict
Rennlist Member
Rennlist Member
worked on the exhaust this weekend: replaced the O2 sensor (I think it was original), the catalytic converter, and the rusty tailpipe. The car runs & sounds great now!
10-07-2012, 11:08 PM
#4442
Rennlist Member
Started it!!!! After 8 months on the jack stands I finally completed the installation of new belts, rollers and seals and it started quite nicely. (It took that long because I am doing serious house renovations and they have taken priority...)
--------------
'87 924S
--------------
'87 924S
10-08-2012, 07:41 AM
#4444
Three Wheelin'
My car did the same thing once, on a blazing hot summer day! It's fairly common. There's a plastic clip that holds the heater flap shut, and the clip breaks leaving the heater flap open. It's located under the dash, in the left side of the center console.
Clarks has more info; http://www.clarks-garage.com/shop-manual/hvac-01.htm
Look at the pic labeled 'HVAC Unit Left Side' It's the clip that holds the rod that goes between part #4 and #5. GL HTH 'Hope This Helps'? or 'Hotter Than Hell'?
Clarks has more info; http://www.clarks-garage.com/shop-manual/hvac-01.htm
Look at the pic labeled 'HVAC Unit Left Side' It's the clip that holds the rod that goes between part #4 and #5. GL HTH 'Hope This Helps'? or 'Hotter Than Hell'?
10-08-2012, 03:10 PM
#4445
Three Wheelin'
10-11-2012, 03:50 AM
#4449
Three Wheelin'
10-11-2012, 06:50 AM
#4450
Three Wheelin'
Thanks Morghen I'm looking forward to this Summer!
lots of 944 love on pistonheads
http://www.pistonheads.com/gassing/t...sche+944&mid=0
not bad for a generic motorsports forum
I'm looking forward to this Summer!lots of 944 love on pistonheads
http://www.pistonheads.com/gassing/t...sche+944&mid=0
not bad for a generic motorsports forum
10-11-2012, 09:28 AM
#4451
Three Wheelin'
Join Date: Jan 2010
Location: Durham Region/GTA East, Canada
Posts: 1,380
Likes: 0
Received 1 Like
on
1 Post
By fiddling, I mean that I unhooked the vac lines, and forced the valve manaully back and forth a few times hoping to free it up. Been fine for the last 4 months.
On topic: Changed the oil, and cleaned the connections on my starter motor while it was on the hoist.
10-11-2012, 09:58 AM
#4452
Intermediate
Join Date: Sep 2012
Posts: 25
Likes: 0
Received 0 Likes
on
0 Posts
I got some 195/65/15's performance winter tires for my fuchs, I didn't even know that tire category existed lol. Got my spec stage 2 clutch in to replace my failing rubber clutch too, but I have no time to put it in, I'm starting my internship soon and going to school, so I may pay to put it in along with a new master and slave, though I don't have the $$$ for it either. The rubber clutch is a mixed blessing, still runs now but I'm cringing every time i get that bad backlash and "clunk", and I'm praying the trans doesn't drop or pop the ring and pinion or clutch fork
*edited* spelling
*edited* spelling
10-11-2012, 10:13 AM
#4453
Three Wheelin'
Join Date: Feb 2002
Location: Arlington, TX
Posts: 1,493
Likes: 0
Received 0 Likes
on
0 Posts
Figured out the reason my fuse was blowing any time I turned on the rear defroster! My driver side hatch strut was installed upside down (it's part of the defroster circuit).
Also fixed the little light in the hatch area.
Also performed the reset procedure on my airbag warning light. Dash is light free now!
Also fixed the little light in the hatch area.
Also performed the reset procedure on my airbag warning light. Dash is light free now!
10-12-2012, 06:56 AM
#4455
Three Wheelin'
will give that a go till I can get the time to fit the new one