What did you do to your GT car today!
#406
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
@Elliotw44 Looks like the vents alone cost about $1600? Or is there a better way to buy DB Carbon stuff?
#407
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
The following users liked this post:
LITEW8GT3 (03-05-2023)
#409
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
reminds me i have to install my new Alcantara center console (porsche carbon completely delaminated)
#410
#412
Rennlist Member
#413
Instructor
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by Wonderdan
very nice, what kind of PPF did you go with? Trying to decide if I go full custom or use the Xpel precut stuff.
#414
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Do custom cut/wrapped edges, installer is key so find a good one. Make sure you talk with them about the hood and being able to fully wrap the edges at the top corners, have a discussion about scoring the film and not cutting through on the paint. Pull the headlights, side markers and headlight washers. Suntek is my preference but comes down to who your installer is setup with.
Precut you will have alot of exposed edges that will collect dirt over time.
Precut you will have alot of exposed edges that will collect dirt over time.
The following users liked this post:
Elliotw44 (02-26-2023)
#415
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Do custom cut/wrapped edges, installer is key so find a good one. Make sure you talk with them about the hood and being able to fully wrap the edges at the top corners, have a discussion about scoring the film and not cutting through on the paint. Pull the headlights, side markers and headlight washers. Suntek is my preference but comes down to who your installer is setup with.
Precut you will have alot of exposed edges that will collect dirt over time.
Precut you will have alot of exposed edges that will collect dirt over time.
#416
Nordschleife Master
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
When a black car is clean, it's a hard color to beat.
![burnout](https://rennlist.com/forums/graemlins/burnout.gif)
The following 2 users liked this post by RAudi Driver:
jonwb (02-27-2023),
Turbo Racer (03-03-2023)
#417
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
New PPF and ceramic coating
Attachment 1334146
Attachment 1334146
#418
Instructor
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by jonwb
Looks fantastic. Do you plan on replacing the GT3 badge? I pulled my badge (also black car) for paint correction work a few years ago and never put it back on.
The following users liked this post:
jonwb (02-27-2023)
#419
Racer
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I don’t notice much, but it’s hard to say as the LWFW and clutch went in at the same time which add some vibrations. Certainly didn’t do anything too harsh. Definitely notice the change to performance though. Rear hooks up much better. Seems like less slack.
Last edited by ThePhanatic; 02-27-2023 at 10:49 PM.
#420
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Smart or not I started doing this about a year ago so I thought I’d share… and just a bit cheaper than a torque multiplier.
After buying the Quickjack I tried something that made my center locks stupid easy…
I just wrap a quick strap on the outside spoke “multiplier” and through my Quickjack and it takes about 30 seconds per wheel…no gear…no parking brake…no wife help… no brake nanny… and no breaking or torquing on the ground. And no it’s not going to “pull my car off” the Jack![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
After buying the Quickjack I tried something that made my center locks stupid easy…
I just wrap a quick strap on the outside spoke “multiplier” and through my Quickjack and it takes about 30 seconds per wheel…no gear…no parking brake…no wife help… no brake nanny… and no breaking or torquing on the ground. And no it’s not going to “pull my car off” the Jack
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)