Note to Porsche classic - 997 PCCM plus request
#1846
I have an AM radio problem. When I last took out my PCCM+, two white wires came loose and disconnected from the main wiring harness. I get fm but no am radio now. Can someone take a picture of their original wiring harness so I can locate where the two white wires go? Thank you.
#1847
Instructor
#1848
If it works you're done.
Last edited by Paul S.; 04-07-2023 at 04:02 PM.
#1849
Intermediate
No clue--maybe another bad SD card. Did your dealer say when they got this card in stock, as you cannot tell any other way because the part numbers and dates don't change? If they've had it prior to the middle of March, I suspect it's the old bad versions.
Something you may try. Did you drive the car after the factory reset or did it just work without the car being started and driven? When I did the factory reset on mine to get the new card working I had no maps or NAV connection sitting still in the driveway outside the garage even with the car running, then it worked when I drove out the driveway and down the street, not far either. About 100 feet.
Something you may try. Did you drive the car after the factory reset or did it just work without the car being started and driven? When I did the factory reset on mine to get the new card working I had no maps or NAV connection sitting still in the driveway outside the garage even with the car running, then it worked when I drove out the driveway and down the street, not far either. About 100 feet.
Going back to the dealer now, but I'm sure I will be met with blank stares and "We don't know what to do now." I do have a case open with Porsche Classic, so I will probably try that route again. Their last advice was to go the dealer who sold me the card. Been there, done that.
#1850
Instructor
For reasons I cannot explain, if like me you had installed one of the "bad" SD cards that wouldn't show states alphabetically after NY, putting in the new card (for me) did nothing/did not work. The PCCM+ was in a perpetual loop searching for satellites. Factory reset and it worked. That's why.
If it works you're done.
If it works you're done.
#1851
Rennlist Member
Just to update - I ordered these four cables from AliExpress on 3/26. They came in two shipments. One arrived (NC) on 4/6 and the other on 4/7. Came USPS. They are VERY small connectors. I don’t have my PCCM+ yet (weeks or months on back order). When it arrives I’ll install as-is for awhile to check everything out. If I can re-pin the Subaru plug to get the pink cable in and open up a pin on the 4-pin connector to know I can do it then I might open up the PCCM+.
#1852
I now have all the cables to re-route the USB ports but I am stuck on one point.
How exactly is the pink cable attached to the Subaru cable? Do I cut the red cable and just solder the three ends together like a Y?
And it looks like I have to swap red and black on my Subaru cable, correct. Then it matches the diagram of @Steve W
Can anyone help me please?
How exactly is the pink cable attached to the Subaru cable? Do I cut the red cable and just solder the three ends together like a Y?
And it looks like I have to swap red and black on my Subaru cable, correct. Then it matches the diagram of @Steve W
Can anyone help me please?
#1853
Instructor
good luck. If it is a bad card, don’t expect much help from them. I ended up ordering another card from Gaudin after it was clear Suncoast wasn’t even interested in trying to help.
#1854
Instructor
I now have all the cables to re-route the USB ports but I am stuck on one point.
How exactly is the pink cable attached to the Subaru cable? Do I cut the red cable and just solder the three ends together like a Y?
And it looks like I have to swap red and black on my Subaru cable, correct. Then it matches the diagram of @Steve W
Can anyone help me please?
How exactly is the pink cable attached to the Subaru cable? Do I cut the red cable and just solder the three ends together like a Y?
And it looks like I have to swap red and black on my Subaru cable, correct. Then it matches the diagram of @Steve W
Can anyone help me please?
Here’s some pics I didn’t get around to posting.
Taped up
Shrink wrap connection
Wire soldered
Pins swapped and red wire out the back.
The following users liked this post:
Bavarian 997 (04-09-2023)
#1857
@dph928 Thanks for your reply, but it's still not 100% clear to me. Sorry to ask again, I don't want to mess up my new PCCM
Wiring like left or right in my diagram?
Wiring like left or right in my diagram?
Connect the red cable to the pink and do NOT connect it back into the pccm....the 5V feeds directly to the 2nd usb, that's it. Then repin the black (negative) to where you pulled the red from.
Below is correct but you only connect it to the pink and do NOT plug it back into the plug. Then switch your black one to the left pin and you are done with this end. (remember pin#1 remains inactive)
Maybe this will help:
John
Last edited by jgoga; 04-08-2023 at 06:27 PM.
The following users liked this post:
Bavarian 997 (04-09-2023)
The following users liked this post:
jgoga (04-09-2023)
The following 2 users liked this post by jgoga:
Bavarian 997 (04-09-2023),
irnnr (04-12-2023)
#1860
My unit is allegedly shipping at the end of this month so I wanted to circle back and see if anyone has tried the “simple solution,” of just routing the front usb out the back and leaving the front non-functioning. With my level of tinkering I’m comfortable with that hack and it’s not worth the extra steps to have the front available for charging.
If anyone has done this already, which cable did you end up using?
If anyone has done this already, which cable did you end up using?