Widowmaker Project - Building a GT2 Clone
#46
Rennlist Member
Thread Starter
#47
Rennlist Member
You guys have good taste. I have their cousin for my other car, as well.
#48
Rennlist Member
Thread Starter
#49
Rennlist Member
Looks awesome. Another VW guy here as well! I still have my MKIV GTI VR6 with a fully built 3.0 L. I actually have a Schimmel Intake sitting in my closet brand new since 2008. I was going to turbo my VR6, but ended up saving and buying my 996 Turbo instead. Sorry if I missed it but are you turboing the corrado, or NA? What do you think of the intake? I was thinking about doing a small project and just installing it in my N/A motor. Schimmel says it will make some power. Great garage!
#50
Rennlist Member
Thread Starter
Looks awesome. Another VW guy here as well! I still have my MKIV GTI VR6 with a fully built 3.0 L. I actually have a Schimmel Intake sitting in my closet brand new since 2008. I was going to turbo my VR6, but ended up saving and buying my 996 Turbo instead. Sorry if I missed it but are you turboing the corrado, or NA? What do you think of the intake? I was thinking about doing a small project and just installing it in my N/A motor. Schimmel says it will make some power. Great garage!
Nice!!! To put the Schimmel SRI on a Mk4 it takes a bit more work due to the throttle body being really close to the fan/battery from what I remember building a supercharger setup for a friend on his. Going N/A on the Corrado for now, I found the SRI and cams are the real way to make big N/A power if you have standalone to really dial it in. Just putting the SRI on a 12v with a chip picks up ~20hp! Originally built the motor for 700hp, but with having the 996/997 to solve the speed bugs a nice N/A light car was the direction that it is headed for now.
A TT downpipe with the SRI are the way to go, what cams are you running on the 3.0?
#51
Rennlist Member
Nice!!! To put the Schimmel SRI on a Mk4 it takes a bit more work due to the throttle body being really close to the fan/battery from what I remember building a supercharger setup for a friend on his. Going N/A on the Corrado for now, I found the SRI and cams are the real way to make big N/A power if you have standalone to really dial it in. Just putting the SRI on a 12v with a chip picks up ~20hp! Originally built the motor for 700hp, but with having the 996/997 to solve the speed bugs a nice N/A light car was the direction that it is headed for now.
A TT downpipe with the SRI are the way to go, what cams are you running on the 3.0?
#52
Rennlist Member
Thread Starter
I'll see if I can dig up some pictures of the setup on my buddies Mk4 for you
#53
Rennlist Member
Fantastic! Much appreciated! Yeah I really enjoy the car. Its not at all fast, but for what it is and the tech it had at the time its really fun. The cams bring on power at 3k and pull all the way up. Quite fun in something that sounds that incredible. Im running a Peloquin LSD and RE71Rs so there is 0 possible chance of wheel spin haha
#54
Rennlist Member
Thread Starter
Fantastic! Much appreciated! Yeah I really enjoy the car. Its not at all fast, but for what it is and the tech it had at the time its really fun. The cams bring on power at 3k and pull all the way up. Quite fun in something that sounds that incredible. Im running a Peloquin LSD and RE71Rs so there is 0 possible chance of wheel spin haha
#55
Rennlist Member
Wow, shame on me for not finding and commenting on this thread sooner.
I grew up with 3 VW Scirocco's myself...a 1977 MKI, a 1982 MK2, and finally a 1988 MK2 16V that I owned back in 1997 when I met my wife-to-be. I only graduated to my first Porsche in 2009 (996TT) but have been fortunate to add a 997.2 GT3 RS and just recently another 996TT. Much like you, doing a GT2 clone is absolutely what I'm pursuing too, and mine has the rear decklid/wing already and I have the GT2 roof skin already too. Kevin @ UMW is my tuner, so love to see the similarities between our styles. I absolutely want to buy a set of those Manthey Racing doors in time, they are on my 'dream list'.
So, kudos to you and thanks for all the great progress photos...I'll be watching with real enthusiasm from the side lines!
I grew up with 3 VW Scirocco's myself...a 1977 MKI, a 1982 MK2, and finally a 1988 MK2 16V that I owned back in 1997 when I met my wife-to-be. I only graduated to my first Porsche in 2009 (996TT) but have been fortunate to add a 997.2 GT3 RS and just recently another 996TT. Much like you, doing a GT2 clone is absolutely what I'm pursuing too, and mine has the rear decklid/wing already and I have the GT2 roof skin already too. Kevin @ UMW is my tuner, so love to see the similarities between our styles. I absolutely want to buy a set of those Manthey Racing doors in time, they are on my 'dream list'.
So, kudos to you and thanks for all the great progress photos...I'll be watching with real enthusiasm from the side lines!
#56
Technical Guru
Rennlist Member
Rennlist Member
Originally Posted by TheDeckMan
Tons of freshly plated hardware.
#57
Rennlist Member
Thread Starter
Wow, shame on me for not finding and commenting on this thread sooner.
I grew up with 3 VW Scirocco's myself...a 1977 MKI, a 1982 MK2, and finally a 1988 MK2 16V that I owned back in 1997 when I met my wife-to-be. I only graduated to my first Porsche in 2009 (996TT) but have been fortunate to add a 997.2 GT3 RS and just recently another 996TT. Much like you, doing a GT2 clone is absolutely what I'm pursuing too, and mine has the rear decklid/wing already and I have the GT2 roof skin already too. Kevin @ UMW is my tuner, so love to see the similarities between our styles. I absolutely want to buy a set of those Manthey Racing doors in time, they are on my 'dream list'.
So, kudos to you and thanks for all the great progress photos...I'll be watching with real enthusiasm from the side lines!
I grew up with 3 VW Scirocco's myself...a 1977 MKI, a 1982 MK2, and finally a 1988 MK2 16V that I owned back in 1997 when I met my wife-to-be. I only graduated to my first Porsche in 2009 (996TT) but have been fortunate to add a 997.2 GT3 RS and just recently another 996TT. Much like you, doing a GT2 clone is absolutely what I'm pursuing too, and mine has the rear decklid/wing already and I have the GT2 roof skin already too. Kevin @ UMW is my tuner, so love to see the similarities between our styles. I absolutely want to buy a set of those Manthey Racing doors in time, they are on my 'dream list'.
So, kudos to you and thanks for all the great progress photos...I'll be watching with real enthusiasm from the side lines!
The roof skin is on my wish list for further down the road to combine it with a final respray of the car. Should be interesting to see the different ways we go about our builds.
After some agony in the past with the push lock fittings, I finally broke down and ordered up a Koul Tool with doing the transmission cooler lines for the 996 and needing to do the lines on the Corrado oil cooler. The $300 that it ended up running was worth every penny as it made several hours of agony using hot water and silicon lube to seat the barbs, to taking less than 2 minutes to do 4 fittings!
Some holes to the lower grille to aid in cooling for the oil cooler and radiator.
Lightening up the front cross member that weighs a ton. Now it can go out to powder coating while waiting on the new thermostat housing and aluminum coolant pipe to show up, then the front end can go back together.
#58
Rennlist Member
Thread Starter
Like all good things, it takes time to get the right parts...some times even more time to get the other parts to use the right parts! In this case it was the long wait on the oil pan ordered up in December for the Corrado, of course while ordering one pan, I figured it would be a good time to pick one up for the Track TT. To my delight they showed up Friday, now time to put the Corrado pan on and continue the forward progress or so I thought.
Out with the old pan and time for the new
Checking out the ARP goodness on the bottom end of the motor with her skirt off
Then things began to not go well. The pan did not seem to fit, after a couple tries to see what was causing the pan to not want to seat against the block, my memory was jogged that these pans were shorter....Yep 4.5" vs 5" so the pickup was hitting the pan. Turns out that a MK5 R32 pump and pickup is needed in order to run the pan.
So the last up was to put the freshly powder coated rebar back onto the Corrado.
Stalled out with the Corrado, I ordered up a new oil pump VW part number 022115105E. So I turned my attention to the 9-3SS rehab project, with it tying up the lift and wanting to get it rolling so the doors/interior could be swapped it was time to tackle the control arms and fix the oil sender leak.
A quick battle with the control arms to replace them was the easy task. Then turning attention to the oil level sender did I discover to reseal it you normally drop the oil pan...With my oil pan success being 0-1 so far, I discovered using some safety wire I could push the sensor into the pan after draining the oil then reseal and pull it back into its position without dropping the pan. Also putting a piece of metal on the other end of the safety wire ensured that the sensor could not slip into the pan completely with the safety wire.
With that sealed up, an oil change and new filter and she is ready to move finally. Hopefully on the road for spring.
Out with the old pan and time for the new
Checking out the ARP goodness on the bottom end of the motor with her skirt off
Then things began to not go well. The pan did not seem to fit, after a couple tries to see what was causing the pan to not want to seat against the block, my memory was jogged that these pans were shorter....Yep 4.5" vs 5" so the pickup was hitting the pan. Turns out that a MK5 R32 pump and pickup is needed in order to run the pan.
So the last up was to put the freshly powder coated rebar back onto the Corrado.
Stalled out with the Corrado, I ordered up a new oil pump VW part number 022115105E. So I turned my attention to the 9-3SS rehab project, with it tying up the lift and wanting to get it rolling so the doors/interior could be swapped it was time to tackle the control arms and fix the oil sender leak.
A quick battle with the control arms to replace them was the easy task. Then turning attention to the oil level sender did I discover to reseal it you normally drop the oil pan...With my oil pan success being 0-1 so far, I discovered using some safety wire I could push the sensor into the pan after draining the oil then reseal and pull it back into its position without dropping the pan. Also putting a piece of metal on the other end of the safety wire ensured that the sensor could not slip into the pan completely with the safety wire.
With that sealed up, an oil change and new filter and she is ready to move finally. Hopefully on the road for spring.
#59
RL Community Team
Rennlist Member
Rennlist Member
Like all good things, it takes time to get the right parts...some times even more time to get the other parts to use the right parts! In this case it was the long wait on the oil pan ordered up in December for the Corrado, of course while ordering one pan, I figured it would be a good time to pick one up for the Track TT. To my delight they showed up Friday, now time to put the Corrado pan on and continue the forward progress or so I thought.
Out with the old pan and time for the new
Checking out the ARP goodness on the bottom end of the motor with her skirt off
Then things began to not go well. The pan did not seem to fit, after a couple tries to see what was causing the pan to not want to seat against the block, my memory was jogged that these pans were shorter....Yep 4.5" vs 5" so the pickup was hitting the pan. Turns out that a MK5 R32 pump and pickup is needed in order to run the pan.
So the last up was to put the freshly powder coated rebar back onto the Corrado.
Stalled out with the Corrado, I ordered up a new oil pump VW part number 022115105E. So I turned my attention to the 9-3SS rehab project, with it tying up the lift and wanting to get it rolling so the doors/interior could be swapped it was time to tackle the control arms and fix the oil sender leak.
A quick battle with the control arms to replace them was the easy task. Then turning attention to the oil level sender did I discover to reseal it you normally drop the oil pan...With my oil pan success being 0-1 so far, I discovered using some safety wire I could push the sensor into the pan after draining the oil then reseal and pull it back into its position without dropping the pan. Also putting a piece of metal on the other end of the safety wire ensured that the sensor could not slip into the pan completely with the safety wire.
With that sealed up, an oil change and new filter and she is ready to move finally. Hopefully on the road for spring.
Out with the old pan and time for the new
Checking out the ARP goodness on the bottom end of the motor with her skirt off
Then things began to not go well. The pan did not seem to fit, after a couple tries to see what was causing the pan to not want to seat against the block, my memory was jogged that these pans were shorter....Yep 4.5" vs 5" so the pickup was hitting the pan. Turns out that a MK5 R32 pump and pickup is needed in order to run the pan.
So the last up was to put the freshly powder coated rebar back onto the Corrado.
Stalled out with the Corrado, I ordered up a new oil pump VW part number 022115105E. So I turned my attention to the 9-3SS rehab project, with it tying up the lift and wanting to get it rolling so the doors/interior could be swapped it was time to tackle the control arms and fix the oil sender leak.
A quick battle with the control arms to replace them was the easy task. Then turning attention to the oil level sender did I discover to reseal it you normally drop the oil pan...With my oil pan success being 0-1 so far, I discovered using some safety wire I could push the sensor into the pan after draining the oil then reseal and pull it back into its position without dropping the pan. Also putting a piece of metal on the other end of the safety wire ensured that the sensor could not slip into the pan completely with the safety wire.
With that sealed up, an oil change and new filter and she is ready to move finally. Hopefully on the road for spring.
#60
Rennlist Member
Thread Starter
Finally got a chance to pull her out for a drive, forgot how much fun the 996 is to toss about. Winter was way too long!
Got a chance to do some cruising with a friend with his 996 Aero.
Got a chance to do some cruising with a friend with his 996 Aero.