PSE Modded 3.6 Mufflers - how close in sound to a real PSE?
07-19-2007, 08:10 PM
#289
Three Wheelin'
I just wanted to add a small note since I have done this change.
My idle as smoothed out. Before it would fluctuate between 600~700, now it stays at 700. In fact sometimes before the change the idle would dip way down then back up again, but this was intermittent and no codes were found. if I ran the A/C it bumped the idle up to 800 and no idle issues occured.
With that said, it doesn't mean that I will get in the car tomorrow and not have the idle fluctuate again, but the times I have driven it since the mod I have not noticed it and before it would of happened by now.
My idle as smoothed out. Before it would fluctuate between 600~700, now it stays at 700. In fact sometimes before the change the idle would dip way down then back up again, but this was intermittent and no codes were found. if I ran the A/C it bumped the idle up to 800 and no idle issues occured.
With that said, it doesn't mean that I will get in the car tomorrow and not have the idle fluctuate again, but the times I have driven it since the mod I have not noticed it and before it would of happened by now.
08-08-2007, 09:05 PM
#291
Three Wheelin'
Originally Posted by hdtwncam88
when you do the MKII exhaust mod to a 3.6 can and install on a 3.4 do you have to reset or do anything to computer ?
You will only need to move the brackets from the 3.4 cans to the 3.6 cans for them to fit, that's it and enjoy
08-08-2007, 09:16 PM
#292
Instructor
Join Date: Jun 2007
Location: Jersey Shore
Posts: 188
Likes: 0
Received 0 Likes
on
0 Posts
Steven that sounds awesome...got mine welded today with 2.125 inch pips and getting installed tomorrow...any tips on the install as far as disconnecting battery or anything i should do ?
Thanks Bernie
Thanks Bernie
08-08-2007, 09:16 PM
#293
Instructor
Join Date: May 2007
Location: Evansville, IN
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TheSpeedDemon
No.
You will only need to move the brackets from the 3.4 cans to the 3.6 cans for them to fit, that's it and enjoy
You will only need to move the brackets from the 3.4 cans to the 3.6 cans for them to fit, that's it and enjoy
08-08-2007, 09:43 PM
#295
Burning Brakes
Join Date: Jan 2007
Location: Miami, Florida
Posts: 1,241
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by hdtwncam88
sorry for the duplicate post my bad...thanks. also contemplating a K&N Cold Air Intake as well
08-08-2007, 09:52 PM
#296
Three Wheelin'
Originally Posted by hdtwncam88
Steven that sounds awesome...got mine welded today with 2.125 inch pips and getting installed tomorrow...any tips on the install as far as disconnecting battery or anything i should do ?
Thanks Bernie
Thanks Bernie
08-08-2007, 09:56 PM
#297
Three Wheelin'
Originally Posted by Alphahunter
What brackets?
You will see that the bracket is the same except for the bolt pattern.
08-08-2007, 11:19 PM
#298
Instructor
Join Date: May 2007
Location: Evansville, IN
Posts: 164
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TheSpeedDemon
Below is a picture of a 3.6 on the left and 3.4 on the right.
You will see that the bracket is the same except for the bolt pattern.
You will see that the bracket is the same except for the bolt pattern.
08-09-2007, 01:11 AM
#300
Drifting
Join Date: Feb 2006
Location: Elk Grove, California
Posts: 2,647
Likes: 0
Received 2 Likes
on
2 Posts
The bolt pattern for the brackets off the 3.6L cans are different than the patterns for the 3.4 cans. You need to trade the brackets off the 3.6 for yours off your stock mufflers....that's the only thing that has to be done. You might have a bit of trouble trying to get the exhaust tips to line up and match....that was the most difficult part of the whole dogone thing.