4 Rings

@Boucherom it’s Matt white but it was from a place called renndecal.

i looked and it doesn’t appear their site is up.

but go look I saw something on Etsy for around $50. It’s the heritage edition lower decal.

Eric Busto

Does anyone have the HRE R101LWs on a C2S using HRE's recommend fitment (20x9.00 ET45 & 21x11.50 ET58)? I'm concerned about the fronts being 1/2" wider than stock, as I don't much care for the stretched look. Is it noticeable? Pictures would be appreciated; I don't trust online renders.

BlitzedTT

But what are the offsets of those wheels? All of the examples appear to be lowered, and likely have a lower offset than 45, so this is not really an accurate representation of the spec that the poster was asking about.

AlterZgo

I don't have HREs, but I'm running 21x9 +48 offset BBS FI-Rs with a 7mm spacer and 255-35-20 tires so this would be equal to a 21x9 +41 offset rim with slightly wider and taller tires than stock. The extra width of the 9" wide front rim will pose no issues w/ the HRE recommended fitment. In fact, on stock 245-35-20 tires, it would be a conservative set up if the car is lowered. If the car is stock height it will be fine. Personally, if I got that set up you have listed for the HREs, I'd still add 7mm spacers F and R. Here are some very detailed info and pictures of my set up if you are curious. Scroll down to the 3rd version of my car w/ the FI-Rs for measurements, picture, etc.

tourenwagen

Not super noticeable. I've had both the Michelins and Pirelli's on my front 9" wide 300 Classics.

The wheels below are the same, just powder coated. In my opinion the Pirelli looks very slightly more stretched on a 9" than the Michelin.

As far as offset goes, I have the same as you quoted above, but I'm running an 18mm spacer up front and a 14mm spacer in the rear.



Michelins:


Pirellis:

T1M3LESS911

I believe those were the initial recommended offsets I got as well from HRE when I was about to order a set of P104SCs back in 2021.

I had a feeling they were a bit conservative since I was running 15mm f/r spacers on my OEM set.

Back then, I wasn’t as familiar with the 992s and considering it was my first set of aftermarket wheels, I didn’t go crazy.

The P104SCs that I had were 20x9 et 45, 21x12 et 60 on OEM tires.

This is how they looked on the car -






While these looked good on the car, I still felt that this was a bit conservative.
There was definitely some room to fit a more aggressive setup/offset.

Second set was HRE Classic 300s
21x9.5, 22x12.5




The Classics were very close in terms the fitment that I personally wanted.. i just felt that the fronts poked a little bit more than the rears…

So in my third set of HREs I went with 21x9.5 (same as the classic 300s) but went with slightly wider rear setup 22x13.. and this set up has no issues whatsoever….

If I ever got a 992 again.., I would do the same wheel set up…. AND these HRE 527S wheels are for sale by the way with tires and TPMS.

tourenwagen

^ every one of your setups have been stellar @T1M3LESS911 but these 527's are just next level!

T1M3LESS911

Appreciate that man! Let me know if you’re ready to switch out of the Classic 300s lol.

I’ll deliver the 527s to you

tourenwagen

Trust me. The thought has crossed my mind

Shogunade

If I didn't have centerlocks I'd just follow @T1M3LESS911 around and pick up his used wheels.

T1M3LESS911

LOL.. not a bad idea.

Did you end up ordering a set of wheels for yourself as well?

WheelsB

Shogunade

Yes. Expecting them any day now.

Master Deep

Any Pros and Cons of Flat Lip vs Step Lip?

Shogunade

Purely from an aesthetic standpoint I have to say the step lip is so much better.