When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Finally acquired a set of Dundon Motorsport intake runners. These are 3d printed from a nylon like material replacing the factory lower intake manifolds, adding 30whp at high rpm on the 991.1 3.8L.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
Last edited by AdamSanta85; 03-05-2023 at 05:56 PM.
I bought a 3M matte red sample for $3 and cut a 1/2” wide strip for the 12:00 marker. Definitely the cheapest mod on my Cayman especially compared to the sport chrono clock that I cut a hole in the dash or the PSE or center radiator……😂
Jim
Finally acquired a set of Dundon Motorsport intake runners. These are 3d printed from a nylon like material replacing the factory lower intake manifolds, adding 30whp at high rpm on the 991.1 3.8L.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
Share your results once you install them. Install looks like a bear!
Also, I don't see these on their website. I just see their metal ones.
Share your results once you install them. Install looks like a bear!
Also, I don't see these on their website. I just see their metal ones.
I think just the prototype was the 3D-printed metal, but all the production ones are 3D-printed plastic. I got these used off at Cayman.
I will make a post once I get the back of the car off, hope to start next week, ordering new gaskets today. I am going to follow the video on YT of the 991.1 IPD plenum install. I feel like if I can get the center out, getting the two lowers off shouldn't be THAT bad.
Last edited by AdamSanta85; 03-06-2023 at 12:05 PM.
Rennline carbon fiber deck louvers & carbon fiber headlight trim. It's a black car so for me the subtle contrast is appreciated.
Love the look of the louvers for sure! Just ordered a set for mine! Were they hard to put on? Sounds like you just pop the OEM's off and attached the CF ones? Is that the case?
Thank you all for your never ending flow of ideas and suggestions. I've had my 991.2 now for about a month, and here is what has happened (or is currently happening).
Almost all ideas from here.
OEM Clear LED Side Markers
OEM Logo Door Projector LEDs
OEM Silver Sports Gas Cap
OEM Valve Caps with Logo
OEM/CTEK Battery Maintainer with Eyelet
OEM Emergency Triangle with Holders (installed)
OEM Wiper Blades (extra set)
Rennline Phone Mount with Charging Cable
Kaizen Cup Holder Replacement for Ashtray
LidLiner Inner Frunk Hood Protector (the “missing factory part”)
SpoilerKing Thin Rear 1.25” Spoiler Lip (Black)
Red Frunk Liner/Box (HD) with Decal (thank you Rennlist)
Frunk Light LED Upgrade
USB Triple Switch Glove Compartment
Uniden Hardwire for R7 Radar Detector from Fuse Box
Garmin Mini-Dashcam with twin Harness from Fuse Box
Missing PDK Lock Trim Tool Replaced
Roadside Emergency Tire Patch Kit
Accident Warning Vest
Black Specialty License Plate with Slim Black Holder
^^^ Welcome! Feel free to share a pic of your new pride & joy!
Thank you - pleasure to be here. And I'll gladly share some pictures, nothing special though: 2019 Base Carrera, PDK, PSE, 20" wheels in black, Sunroof, BOSE, K40 Platinum360 with Laser Defuser, and cooled seats for Florida.
... and then the stuff I added later.
Last edited by Frankfurt1470; 03-07-2023 at 09:44 PM.
Love the look of the louvers for sure! Just ordered a set for mine! Were they hard to put on? Sounds like you just pop the OEM's off and attached the CF ones? Is that the case?
It's easy enough but it does require a few steps starting with the removal of the entire louver deckled cover. Thats 4 t25 bolts and two pinch clips, then unhook the third brake light. Once removed from the car, the individual louvers need to be unclipped from the bracket one at a time. You have to work from top to bottom and install in the same order of removal. About 45 minutes since I took my time. Could do in 15 if I was in a rush now that I understand the steps.
By any chance, does anyone know if the following parts will fit my car, the 2019 Base Carrera?
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
Thanks.
Last edited by Frankfurt1470; 03-08-2023 at 12:18 AM.
By any chance, does anyone know if the following parts will fit my car, the 2019 Base Carrera?
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
03-05-2023, 04:28 AM
