What did you buy your 991 today thread
#7711
Drifting
^^^ Nice wheels!
#7712
Nordschleife Master
what is that 12:00 marker on your steering wheel?
#7713
Rennlist Member
Finally acquired a set of Dundon Motorsport intake runners. These are 3d printed from a nylon like material replacing the factory lower intake manifolds, adding 30whp at high rpm on the 991.1 3.8L.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
Last edited by AdamSanta85; 03-05-2023 at 05:56 PM.
The following 9 users liked this post by AdamSanta85:
desmotesta (03-06-2023),
GermanCarFan1 (03-05-2023),
jesm (03-05-2023),
jfischet (03-06-2023),
PathfinderGTS (03-05-2023),
and 4 others liked this post.
#7714
#7715
I bought a 3M matte red sample for $3 and cut a 1/2” wide strip for the 12:00 marker. Definitely the cheapest mod on my Cayman especially compared to the sport chrono clock that I cut a hole in the dash or the PSE or center radiator……😂
Jim
Jim
#7716
Rennlist Member
Finally acquired a set of Dundon Motorsport intake runners. These are 3d printed from a nylon like material replacing the factory lower intake manifolds, adding 30whp at high rpm on the 991.1 3.8L.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
My existing setup is catted Fabspeed headers, Cargraphic cat back, AFE dual cone intake, Cobb AP with M Engineering tune. I was advised to stick with stock center plenum.
Hoping for close to 400whp on 93 octane.
Also, I don't see these on their website. I just see their metal ones.
Last edited by Joec500; 03-05-2023 at 11:42 PM.
#7717
Rennlist Member
I will make a post once I get the back of the car off, hope to start next week, ordering new gaskets today. I am going to follow the video on YT of the 991.1 IPD plenum install. I feel like if I can get the center out, getting the two lowers off shouldn't be THAT bad.
Last edited by AdamSanta85; 03-06-2023 at 12:05 PM.
#7718
Rennlist Member
Love the look of the louvers for sure! Just ordered a set for mine! Were they hard to put on? Sounds like you just pop the OEM's off and attached the CF ones? Is that the case?
Last edited by Viper1000; 03-06-2023 at 08:48 PM.
#7719
Advanced
Thank you all for your never ending flow of ideas and suggestions. I've had my 991.2 now for about a month, and here is what has happened (or is currently happening).
Almost all ideas from here.
Additionally:
Almost all ideas from here.
- OEM Clear LED Side Markers
- OEM Logo Door Projector LEDs
- OEM Silver Sports Gas Cap
- OEM Valve Caps with Logo
- OEM/CTEK Battery Maintainer with Eyelet
- OEM Emergency Triangle with Holders (installed)
- OEM Wiper Blades (extra set)
- Rennline Phone Mount with Charging Cable
- Kaizen Cup Holder Replacement for Ashtray
- LidLiner Inner Frunk Hood Protector (the “missing factory part”)
- SpoilerKing Thin Rear 1.25” Spoiler Lip (Black)
- Red Frunk Liner/Box (HD) with Decal (thank you Rennlist)
- Frunk Light LED Upgrade
- USB Triple Switch Glove Compartment
- Uniden Hardwire for R7 Radar Detector from Fuse Box
- Garmin Mini-Dashcam with twin Harness from Fuse Box
- Missing PDK Lock Trim Tool Replaced
- Roadside Emergency Tire Patch Kit
- Accident Warning Vest
- Black Specialty License Plate with Slim Black Holder
Additionally:
- OEM Front Feeler Lip replaced - Warranty
- OEM Washer Fluid Hose replaced - Warranty
- OEM Battery replaced - Warranty
The following 2 users liked this post by Frankfurt1470:
The Albatross (03-07-2023),
Wing Commander (03-07-2023)
#7720
Drifting
^^^ Welcome! Feel free to share a pic of your new pride & joy!
#7721
Advanced
Thank you - pleasure to be here. And I'll gladly share some pictures, nothing special though: 2019 Base Carrera, PDK, PSE, 20" wheels in black, Sunroof, BOSE, K40 Platinum360 with Laser Defuser, and cooled seats for Florida.
... and then the stuff I added later.
... and then the stuff I added later.
Last edited by Frankfurt1470; 03-07-2023 at 09:44 PM.
The following 3 users liked this post by Frankfurt1470:
The following users liked this post:
Nixin (03-09-2023)
#7723
It's easy enough but it does require a few steps starting with the removal of the entire louver deckled cover. Thats 4 t25 bolts and two pinch clips, then unhook the third brake light. Once removed from the car, the individual louvers need to be unclipped from the bracket one at a time. You have to work from top to bottom and install in the same order of removal. About 45 minutes since I took my time. Could do in 15 if I was in a rush now that I understand the steps.
#7724
Advanced
By any chance, does anyone know if the following parts will fit my car, the 2019 Base Carrera?
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
Thanks.
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
Thanks.
Last edited by Frankfurt1470; 03-08-2023 at 12:18 AM.
#7725
Three Wheelin'
By any chance, does anyone know if the following parts will fit my car, the 2019 Base Carrera?
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
Thanks.
991-504-595-03-1E0
991-504-596-03-1E0
i’m not sure if that’s the correct term, but I’d like to put some rocker panels or side skirts on the sides under the doors from wheel to wheel. Nothing too prominent, just something to make the plain white edge under the door a bit nicer to look at. Unpainted in matte black.
has anybody maybe used these and can post a picture?
Thanks.