991 GT2/3RS strakes on GT3...
#31
Rennlist Member
This thread is awesome! After Jamie at Dundon said he thought the 992 strakes would fit on the 991.2GT3 I called around to inquire about the parts and got nowhere. Now armed with the actual part numbers I called one of my local dealers and all for are available stateside and priced at $133 each. I would image Suncoast may have better pricing.
#32
Rennlist Member
Thread Starter
Here's my total from Sunset Porsche Parts, with free shipping. Just waiting for @Diego7K to confirm fitment before ordering!
Last edited by Larry Cable; 07-11-2022 at 08:39 PM.
#33
Rennlist Member
Thread Starter
#35
Rennlist Member
Originally Posted by Larry Cable;[url=tel:18243799
18243799[/url]]are those F&R?
The Emotion strakes are a copy of these minus the wheel arch air guide.
The strakes on the GT4RS are very similar to these as well.
#36
Rennlist Member
Thread Starter
#37
Rennlist Member
GT4RS strakes. Green and red ones are close in design in the 991.2 MR kit.
The following users liked this post:
Larry Cable (07-12-2022)
#38
Rennlist Member
Thread Starter
#39
Rennlist Member
Originally Posted by Larry Cable;[url=tel:18244832
18244832]are they two separate pieces?
Last edited by Wind911; 07-12-2022 at 12:57 PM.
The following users liked this post:
Larry Cable (07-12-2022)
#40
If they are 3 actual separate pieces, shouldn't we have 3 sets of part numbers instead of 2?
Apologies if I'm missing something here, waiting to place an order once Diego7K confirms fitment as well.
Apologies if I'm missing something here, waiting to place an order once Diego7K confirms fitment as well.
#41
Rennlist Member
Thread Starter
#42
Rennlist Member
Installation of the 992 GT3 parts on going, can be reused some oem mounting points, but need some additional screws as well.
Front tires have 5mm clearance with the wheel arch guide, steering at full lock, lift up
Front tires have 5mm clearance with the wheel arch guide, steering at full lock, lift up
The following users liked this post:
DiscoWagon (07-13-2022)
#43
Rennlist Member
I actually think the GT4RS pieces might fit better on the 991 cars. Since the 982 front tub is almost identical to the 991. It might not need any additional holes.
The following users liked this post:
RDCR (07-13-2022)
#44
Rennlist Member
Thread Starter
Appreciate the effort. That look very close. Is it also this close on the 992 GT3?
GT4RS has 3 pieces per side. 992 GT3 has 2.
I actually think the GT4RS pieces might fit better on the 991 cars. Since the 982 front tub is almost identical to the 991. It might not need any additional holes.
GT4RS has 3 pieces per side. 992 GT3 has 2.
I actually think the GT4RS pieces might fit better on the 991 cars. Since the 982 front tub is almost identical to the 991. It might not need any additional holes.
we should try and get the p/n's!
The following users liked this post:
RDCR (07-13-2022)
#45
Rennlist Member
992 GT3 parts installed! Installation was quite strait forward, just 4x additional screw mounting points per side. Fitment I would say is 9/10, for sure GT4RS parts will fit even better (unfortunately no pictures of the 4RS underbody were available when I purchased the parts, otherwise I would taken this route), anyway I'm happy with the result.
The following 3 users liked this post by Diego7K: