New Steering Intermediate Shafts for the 944 - SALE
#31
Instructor
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
so apparently these shafts are crap(at least some patch of em)... any quality options out there ? (i use it for a year and now theres play)
Last edited by Aivar88; 03-28-2019 at 12:01 PM.
#35
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
No manual options at this time. I think you can get just the splined shafts from Summit Racing in the correct manual length. You could then swap over the ends, if you were so inclined. They are swagged in place, not welded so removal would be possible. I haven't tried it yet so just speculation.
#36
Rennlist Member
#37
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
For the dictionary definition of, “triggered” (are people still using that word? I guess old people on the internet still are?), see Magfag’s posts here: https://rennlist.com/forums/924-931-...l#post15660271
“Mike” what? Only the coward can say.
“Mike” what? Only the coward can say.
#38
Burning Brakes
Join Date: Sep 2017
Location: Formerly the DPRK, now seeking political asylum in Oregon
Posts: 1,162
Received 589 Likes
on
355 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
It's just a straight shaft with U Joints on it.
It's not heavily loaded.
It IS an important piece, but i wouldn't hesitate to make my own when I need to.
BMW E36 has aluminum U joints in theirs, splined on both ends. I'll bet every ZF rack has the same splines...
It's not heavily loaded.
It IS an important piece, but i wouldn't hesitate to make my own when I need to.
BMW E36 has aluminum U joints in theirs, splined on both ends. I'll bet every ZF rack has the same splines...
#40
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
The bearings are available separately,. Getting the joints apart without damaging the yokes requires some careful work. For situations where you have a manual rack, but no intermediate shaft, I'd have a custom shaft to be fitted to your yokes. I was going to go that route until I happened across the correct shaft for sale on E-Bay.
#42
Rennlist Member
#43
Rainman
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
you would think, but remember for most of the 20th century US equipment and products dominated the world of manufacturing.
a lot of stuff is spec'd in inches and just converted "approximately" to metric for the ROW to understand.
AC fittings, all types of rubber hose, timing belts are all SAE/inch.
hell, i have an original VOLVO 740 radiator in my garage and the trans cooler fittings are 1/2"-20 UNF.
but the 740 turbo's original engine oil cooler uses 1/2" british pipe fittings...
a lot of stuff is spec'd in inches and just converted "approximately" to metric for the ROW to understand.
AC fittings, all types of rubber hose, timing belts are all SAE/inch.
hell, i have an original VOLVO 740 radiator in my garage and the trans cooler fittings are 1/2"-20 UNF.
but the 740 turbo's original engine oil cooler uses 1/2" british pipe fittings...
#44
#45
Drifting
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Hi - can you tell me where I can but one of these shafts? drtucker@esatclear.ie