project: turbocharging 944 N/A the proper way
#512
Addict
Rennlist Member
Rennlist Member
Thread Starter
Instructions are very clear about that.. Sicherungsklotz FTW
#513
Addict
Rennlist Member
Rennlist Member
Thread Starter
Got cheap new vented cap. Fits perfectly. Evap stuff can now go where it belongs.
And another small detail that arrived today
And another small detail that arrived today
Last edited by Voith; 05-23-2018 at 08:57 AM.
#514
Addict
Rennlist Member
Rennlist Member
Thread Starter
Final piece of longblock puzzle just arrived
#515
Addict
Rennlist Member
Rennlist Member
Thread Starter
I have to be one of the biggest defect gaskets magnet the world has ever seen.
#516
Addict
Rennlist Member
Rennlist Member
Thread Starter
Recieved dual gauge pod from SamGrant951 for free. Thanks Sam! Nothing beats free nice car parts
This together with 996 radio delete cubby will look spectacular.
This together with 996 radio delete cubby will look spectacular.
#517
Addict
Rennlist Member
Rennlist Member
Thread Starter
Time to end hibernation and pour some love in to this again..
Between last post and now, we have built new house to some degree and moved in to it plus got another family member named Aleksander, so now we are small but loud family of 4.
Recently I had one of my bright moments and determined it's not really water cooled until it's water cooled. So I cut apart 968, XJR and 951 intake manifolds. I'll try to make something useful out of them. And while I was in cutting mode, I cut exhaust manifold too.
Between last post and now, we have built new house to some degree and moved in to it plus got another family member named Aleksander, so now we are small but loud family of 4.
Recently I had one of my bright moments and determined it's not really water cooled until it's water cooled. So I cut apart 968, XJR and 951 intake manifolds. I'll try to make something useful out of them. And while I was in cutting mode, I cut exhaust manifold too.
#519
Addict
Rennlist Member
Rennlist Member
Thread Starter
#520
Addict
Rennlist Member
Rennlist Member
Thread Starter
DME & KLR
#521
Addict
Rennlist Member
Rennlist Member
Thread Starter
Got the correct 45/2mm SS304 pipe for exhaust manifold
And an old huge 400 volt bandsaw with mechanical reductor gearbox
Screwed up this one..
#522
Race Car
#523
Addict
Rennlist Member
Rennlist Member
Thread Starter
Will buy new aluminum pipe today and try that next.
I'm using biax but aluminum gets in the bit and I have to clean it every 2 minutes. Pure alumunum is such a pita to work with. End mill bit would probably help.
bought this one yesterday, old chinese no name I had blew apart.. Junk.
I'm using biax but aluminum gets in the bit and I have to clean it every 2 minutes. Pure alumunum is such a pita to work with. End mill bit would probably help.
bought this one yesterday, old chinese no name I had blew apart.. Junk.
Last edited by Voith; 04-24-2020 at 03:57 AM.
#525
Rainman
Rennlist Member
Rennlist Member
Goran - don't they sell "hole saws" in your part of the world?
I see you get WD40..
Be very careful with that grinder bit you have there; aluminum is soft and will gum up the bit and can break it if it digs in too hard. Only give it very light touches.
I see you get WD40..
Be very careful with that grinder bit you have there; aluminum is soft and will gum up the bit and can break it if it digs in too hard. Only give it very light touches.