CarPlay Retrofit in PCM 3.1 Cayenne 2013 ( With Pictures )
#1441
Intermediate
I ordered it directly from, mr12volt, in hindsight I suppose I should have ordered it from you. I hope it has the correct standoffs, do you know what size they are?
Last edited by sdl2112; 04-15-2023 at 08:09 AM.
#1442
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Haha, if your car has sat radio, it won't.
__________________
Modernize your P-Car w/ Mr12Volt. Apple Carplay and Android Auto with superior audio quality, features, and support. Reach out for specials! Torque.Acs@gmail.com or Roman (267) 317-8229
Our website is now LIVE! please visit us at www.ACSByRoman.com
FREE INSTALL KIT AND CAR CHARGER WHILE SUPPLIES LAST!
On site install is available in the Philadelphia PA area as is Global shipping!
CLICK HERE JOIN OUR FACEBOOK GROUP
Our website is now LIVE! please visit us at www.ACSByRoman.com
FREE INSTALL KIT AND CAR CHARGER WHILE SUPPLIES LAST!
On site install is available in the Philadelphia PA area as is Global shipping!
CLICK HERE JOIN OUR FACEBOOK GROUP
#1443
if I remember correctly, you’ll need 21-22mm stand-off. In my case I had to put two of them together to get to correct height. Buy an assorted stand-off box from Amazon.
Mr12Volt Carplay Module Installation - PCM3.1 - Porsche Macan 2015
#1444
Intermediate
Bummer, I knew you did the installs but didn’t think to ask if you sold the units alone. I’m near Austin Tx so not local.
Do you know the size please?…I thought I read it’s M2.5x 21mm ?
Also I’m not sure what version software it will have, is it only updated by the SD slot or can it be by USB. The website says by SD slot but here it shows by USB so…
Thanks for your help!
Do you know the size please?…I thought I read it’s M2.5x 21mm ?
Also I’m not sure what version software it will have, is it only updated by the SD slot or can it be by USB. The website says by SD slot but here it shows by USB so…
Thanks for your help!
#1445
For the boot logo, is there a setup file that needs to be included with the image on the USB thumb drive? Also can you update the firmware through USB or only through the SD slot. I asked Mr12volt but no response. If someone has the setup file that would be great…thx. I should be getting my unit today!
UPDATE: Mr12Volt Boot Up Logo change and Factory Mic Hack
#1446
Bummer, I knew you did the installs but didn’t think to ask if you sold the units alone. I’m near Austin Tx so not local.
Do you know the size please?…I thought I read it’s M2.5x 21mm ?
Also I’m not sure what version software it will have, is it only updated by the SD slot or can it be by USB. The website says by SD slot but here it shows by USB so…
https://www.youtube.com/watch?v=obgdTE8O9pQ
Thanks for your help!
Do you know the size please?…I thought I read it’s M2.5x 21mm ?
Also I’m not sure what version software it will have, is it only updated by the SD slot or can it be by USB. The website says by SD slot but here it shows by USB so…
https://www.youtube.com/watch?v=obgdTE8O9pQ
Thanks for your help!
Other Updates (like boot logo) need to be done via USB.
That had been my experience….
from Amazon: LANMU Micro SD to Micro SD Card Extension Cable Adapter Flexible Extender Compatible with Ender 3 Pro/Ender 3/Ender 3 V2/Ender 5 Plus/Ender 5 Pro/CR-10S Pro/Raspberry Pi(5.9in/15cm) https://a.co/d/b8Znkvr
Last edited by Santirx; 04-15-2023 at 08:42 AM.
#1448
M2.5 hex
These are the ones I bought from Amazon… assorted heights…. As I said, I had to use 2 (one on top of the other) in each location… I believe I used 15mm+6mm at each location.
Electronics-Salon Metric M2.5 Hex... https://www.amazon.com/dp/B072N84VM3?ref=ppx_pop_mob_ap_share
BTW, thanks for subscribing to the channel…
Last edited by Santirx; 04-15-2023 at 10:02 AM.
The following users liked this post:
sdl2112 (04-15-2023)
#1449
I have tried the boot logo update a couple times per the file on the Youtube page and an image saved as instructed. When I start up the radio with the USB installed, it just thinks it is a USB with music and does not update anything. Anyone else update their boot logo and got it to work?
#1452
#1453
Unfortunately I cannot get it to update. I tried FAT default 32 and I tried exFAT16 since I did not see a way to format to FAT16. I reduced the size of the picture to 400x240. With both FAT32 and the default format, the system appears to recognize it, but was trying to read for songs. The exFAT16 did not do anything. My USB is only a 2GB drive. Other than plugging in the USB and turning on the radio, is there anything else needed to be done? I went into settings, but did not select anything.