Jackpoint Jackstands ???
#31
Nordschleife Master
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Yes, simple, elegant and SAFE. As far as going higher, maybe a two-stage jacking procedure, where an extension (just a round "tube") could be placed on top the the base for an extra 6 inch or so... (extra ace$$ory $ales opportunity)
Have you tested to failure? How heavy until the legs start to spread - across the opening?
Group buy... to increase visibility at tracks around North America.
Have you tested to failure? How heavy until the legs start to spread - across the opening?
Group buy... to increase visibility at tracks around North America.
#35
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
anyone know if these work with an ac jack model dk13hlq?
just by eyeballing it, the jack arm looks like it would be a tight fit at best
I have not measured yet but thought I would ask before I got inspired :-)
just by eyeballing it, the jack arm looks like it would be a tight fit at best
I have not measured yet but thought I would ask before I got inspired :-)
#39
#40
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
appreciate it
wheel width is about 11 i am told... called my wife had her measure it
jack pad - fine
jack arm she says is 6 inches wide - I will be able to measure it myself later this week
let me know what you find and if inconclusive I will take measurement pics and post etc
wheel width is about 11 i am told... called my wife had her measure it
jack pad - fine
jack arm she says is 6 inches wide - I will be able to measure it myself later this week
let me know what you find and if inconclusive I will take measurement pics and post etc
#41
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
AC does not publish the dimensions of the Jack pad or the Jack Arm width. Both are critical for the smooth operation of this product. I don't think that Jack pad will be an issue, however the Jack arm should be 5 1/2 inches or less in width for the smoothest operation. If the AC arm is 6 inches wide, I'm afraid this stand will not accommodate it at this time. Please let me know what you learn when you measure it.
#43
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I saw these at the Porsche Parade this summer and bought two pairs. They are fantastic and easy to use. Also, You only need to drive on a 2 x 8 at one wheel location if you have a GT3 nor similar LOW ride height car. Once one corner is jackstanded, getting the jack + frisbee under the other wheels is no longer an issue. ( I jack front wheels first)
#44
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
With the low profile pad, you might be able to skip the 2X on standard ride height GT3's. It depends on your particular jack. With some cars, jacking one corner up to slightly unload the suspension and letting the car down will give enough height to get a jack with the pad in place under the car. That was enough for a HFT 1.5 ton aluminum jack on some lowered cars.
![thumbup](https://rennlist.com/forums/graemlins/thumbup.gif)
![Big Grin](https://rennlist.com/forums/images/smilies/biggrin.gif)
#45
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
So... I took some crappy iphone pics this morning on the way out the door... while the quality is not that great, I think they are sufficient for my needs here.
Also, I can do the math so I am posting these here for the benefit of the manufacturer and distributor and any other RLers that were curious about using this jack with these jack stands.
so... overall picture of the jack
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/032.jpg)
Per the instructions on the IMGT3 website
http://www.imgt3performance.com/User...structions.pdf
The jack plate must be 3-5 inches in diameter
here is a pic of the jack plate base - which will work... I neglected to measure the actual jack plate pad that you can see in the picture above, but I think it is alright.
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/035.jpg)
The jack base should be 11.75 inches or less - so we are good
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/037.jpg)
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/038.jpg)
The jack lift arm should be 5.5 inches or less -- we are not good
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/034.jpg)
as you can see the jack arm is the limiting factor 5.625" when the instructions detail 5.5 or less...
It is very close -- close enough that a grind in the right spot might "make it work" but I am not too keen on grinding the jack stands or the jack at this point.
So -- is it close enough that it will work without modification?
In any event, I hope this has been helpful.
Also, I can do the math so I am posting these here for the benefit of the manufacturer and distributor and any other RLers that were curious about using this jack with these jack stands.
so... overall picture of the jack
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/032.jpg)
Per the instructions on the IMGT3 website
http://www.imgt3performance.com/User...structions.pdf
The jack plate must be 3-5 inches in diameter
here is a pic of the jack plate base - which will work... I neglected to measure the actual jack plate pad that you can see in the picture above, but I think it is alright.
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/035.jpg)
The jack base should be 11.75 inches or less - so we are good
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/037.jpg)
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/038.jpg)
The jack lift arm should be 5.5 inches or less -- we are not good
![](http://i212.photobucket.com/albums/cc36/pjsgt3/AC%20Jack/034.jpg)
as you can see the jack arm is the limiting factor 5.625" when the instructions detail 5.5 or less...
It is very close -- close enough that a grind in the right spot might "make it work" but I am not too keen on grinding the jack stands or the jack at this point.
So -- is it close enough that it will work without modification?
In any event, I hope this has been helpful.