New SC Kit for the '85/86
#1
Developer
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Here's a sneak peak at the next SC kit to roll out of the 928 Motorsports Garage:
I'll try to get it dyno'd somewhere between now and Jan 10th. I already have a base-line dyno from this car pre-supercharged.
It will be priced at $4,895.00 complete.
It features an air-cooled Raptor supercharger with a ceramic coated impeller for the absolute lowest charged air temp possible.
We took a heck of a long time to develop that air filter assembly - but its a perfect fit on all years/models. I just didn't like the idea of telling a customer to cut a 3.5" hole in an inner fender to fit their cold-air intake. Now we can get cold air without that.
Merry Christmas!
I'll try to get it dyno'd somewhere between now and Jan 10th. I already have a base-line dyno from this car pre-supercharged.
It will be priced at $4,895.00 complete.
It features an air-cooled Raptor supercharger with a ceramic coated impeller for the absolute lowest charged air temp possible.
We took a heck of a long time to develop that air filter assembly - but its a perfect fit on all years/models. I just didn't like the idea of telling a customer to cut a 3.5" hole in an inner fender to fit their cold-air intake. Now we can get cold air without that.
Merry Christmas!
#3
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Nice looking setup, what kind of boost will it make as pictured? Any fuel mapping, work on LH or EZK chips? Did you use any knock detection, whether just indicator only or timing retardation? What are doing for fan, looks like only the front A/C fan.
Last edited by Glen McCartney; 12-21-2007 at 07:35 PM. Reason: Added questsion
#5
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Carl...If you flip the intake to the pax side on that set up, guys running the old TS set ups Im sure would be interested! Nicely done!
Never heard of "Raptor"? Then again Im out of the loop on all this stuff now.
What FMU is that?
Never heard of "Raptor"? Then again Im out of the loop on all this stuff now.
What FMU is that?
#7
Developer
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
The Raptor is an inernally-belt driven supercharger that is milled from a billet.
It is made in Australia and we are the sole North American importer for it. I have been their dealer for going on two years now.
The Raptor was the best blower I could find bar-none for our Ferrari Mondial and 308 supercharger kits.
http://www.928motorsports.com/parts/...percharger.php
Being belt-driven and permanently-lubricated means 1) simpler installation as you do not have to run oil lines to or from the blower, and 2) cooler charge air temps (better adiabatic efficientcy) than crankcase-oiled superchargers.
Think about it... engine oil gets to 220 degrees regularly, if you lubricate your supercharger with that, you can rest assured that the supercharger will also attain that temperature. Then add the temp increase from compressing air - and the outlet air temp gets plenty hot. An Intercooler corrects this.
But here, on the 85/86, there is no room for an intercooler. So I opted to bring the Raptor over from our Ferrari kits because a) we have had really good success with them on the higher-revving Ferraris (7000 and 7500 rpm redlines), and b) their outlet temp is low enough that they are much safer to run without an intercooler.
You can read more about the Raptor here:
http://www.928m.com/parts/raptorsuperchargers.php
BTW: the price of $4,895.00 complete is a $600 reduction from the price of our previous Powerdyne kit for the same year/model of 928:
http://www.928motorsports.com/parts/32vstage1.php
How 'bout that!
It is made in Australia and we are the sole North American importer for it. I have been their dealer for going on two years now.
The Raptor was the best blower I could find bar-none for our Ferrari Mondial and 308 supercharger kits.
http://www.928motorsports.com/parts/...percharger.php
Being belt-driven and permanently-lubricated means 1) simpler installation as you do not have to run oil lines to or from the blower, and 2) cooler charge air temps (better adiabatic efficientcy) than crankcase-oiled superchargers.
Think about it... engine oil gets to 220 degrees regularly, if you lubricate your supercharger with that, you can rest assured that the supercharger will also attain that temperature. Then add the temp increase from compressing air - and the outlet air temp gets plenty hot. An Intercooler corrects this.
But here, on the 85/86, there is no room for an intercooler. So I opted to bring the Raptor over from our Ferrari kits because a) we have had really good success with them on the higher-revving Ferraris (7000 and 7500 rpm redlines), and b) their outlet temp is low enough that they are much safer to run without an intercooler.
You can read more about the Raptor here:
http://www.928m.com/parts/raptorsuperchargers.php
BTW: the price of $4,895.00 complete is a $600 reduction from the price of our previous Powerdyne kit for the same year/model of 928:
http://www.928motorsports.com/parts/32vstage1.php
How 'bout that!
Trending Topics
#9
Under the Lift
Lifetime Rennlist
Member
Lifetime Rennlist
Member
#10
Craic Head
Lifetime Rennlist
Member
Lifetime Rennlist
Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Carl,
Amazing! That is a work of art. Really nice!
Will you make that filter setup available as a separate part? If so, I'd like to order one NOW!
Amazing! That is a work of art. Really nice!
Will you make that filter setup available as a separate part? If so, I'd like to order one NOW!
#11
In Your Face, Ace
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
As always, another super nice product from 928 Motorsports!
What are the boost levels on the stock kit?
And are you providing a new ECU chip for the LH?
What are the boost levels on the stock kit?
And are you providing a new ECU chip for the LH?
#12
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Carl, will that intake/filter setup work with my S/C kit ? If so wll you please add it to my order?
Looks really great
nice job !
Tass
Looks really great
![jumper](https://rennlist.com/forums/graemlins/jumper.gif)
Tass
Last edited by Tass 928; 12-22-2007 at 10:43 AM.
#15
Burning Brakes
Join Date: May 2006
Location: Portland, Oregon
Posts: 809
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Louie is building a cold air intake something like this for my SC'd GT.
It looks like the filter is being sucked on very hard right at the inlet, which makes sense. I am just wondering how much volume the left 1/2 (passenger side)of the filter really adds? I mean it can't hurt but is the left half really adding much usable volume? This is not a critique, just a question. That is very nice and the best intake option by far for the pre 928SP Twin Screw guys, if you offer it to them.
Jim
It looks like the filter is being sucked on very hard right at the inlet, which makes sense. I am just wondering how much volume the left 1/2 (passenger side)of the filter really adds? I mean it can't hurt but is the left half really adding much usable volume? This is not a critique, just a question. That is very nice and the best intake option by far for the pre 928SP Twin Screw guys, if you offer it to them.
Jim
Last edited by pmotts; 12-22-2007 at 01:11 PM.