Twin Turbo 928 fixed and back out there terrorizing the streets!
#1651
Nordschleife Master
Thread Starter
I'm on the top of the hill in our little town and the street leading to my driveway is the steepest road in town. You have to give a car some gas to go up that road, hence the problem.
#1652
Racer
Why not park it in the bat cave, Alfred too busy to make room in the garage?
just kidding
I've been following this thread forever it seems.
Nice work Alfred has done this far.
#1653
Rennlist Member
Jase.
#1655
Nordschleife Master
Thread Starter
What's that intake manifold in your avatar?
Last edited by ptuomov; 07-16-2017 at 09:44 AM.
#1659
Nordschleife Master
Thread Starter
A quick update: Accident, damage, delay, and back in the saddle
A quick update after the summer: A little over a month ago John had an accident in his job that destroyed some parts. A heavy welding rig collapsed. Fortunately, nobody was under it and there were no lives or limbs lost. Unfortunately, one of the parts that was damaged beyond repair was a prototype cast exhaust manifold. What this meant is that we were back to 3D printing clay/sand molds and pouring high-silicon cast iron. That amounted to about two month delay once you factor in the machining operations, thermal barrier coatings, etc. I'll post some photos of the new casting soon, it's slightly improved prototype because the shrinkage factors etc. could be estimated very precisely from the previous prototype casting.
#1660
Nordschleife Master
Thread Starter
A quick update after the summer: A little over a month ago John had an accident in his job that destroyed some parts. A heavy welding rig collapsed. Fortunately, nobody was under it and there were no lives or limbs lost. Unfortunately, one of the parts that was damaged beyond repair was a prototype cast exhaust manifold. What this meant is that we were back to 3D printing clay/sand molds and pouring high-silicon cast iron. That amounted to about two month delay once you factor in the machining operations, thermal barrier coatings, etc. I'll post some photos of the new casting soon, it's slightly improved prototype because the shrinkage factors etc. could be estimated very precisely from the previous prototype casting.
#1661
Nordschleife Master
Thread Starter
A quick update after the summer: A little over a month ago John had an accident in his job that destroyed some parts. A heavy welding rig collapsed. Fortunately, nobody was under it and there were no lives or limbs lost. Unfortunately, one of the parts that was damaged beyond repair was a prototype cast exhaust manifold. What this meant is that we were back to 3D printing clay/sand molds and pouring high-silicon cast iron. That amounted to about two month delay once you factor in the machining operations, thermal barrier coatings, etc. I'll post some photos of the new casting soon, it's slightly improved prototype because the shrinkage factors etc. could be estimated very precisely from the previous prototype casting.
#1663
Nordschleife Master
Thread Starter
I've got a lot of pictures, not all appropriate for a Porsche site.
Here's one though, it's from a Croatian WW2 U-boat shelter.
So we went into a bomb shelter but still got totally Blitzed! ;-)
#1664
Addict
Rennlist Member
Rennlist Member
Join Date: Oct 2003
Location: Gone. On the Open Road
Posts: 16,467
Received 1,623 Likes
on
1,060 Posts
Tuomo new enforcement going into effect 10/1. FYI.
http://www.thedrive.com/sheetmetal/1...ection-program
http://www.thedrive.com/sheetmetal/1...ection-program
#1665
Nordschleife Master
Thread Starter
Tuomo new enforcement going into effect 10/1. FYI.
http://www.thedrive.com/sheetmetal/1...ection-program
http://www.thedrive.com/sheetmetal/1...ection-program
Good to get to car content and step away from the vacation talk. This sort of vacation photos from Hvar would be totally off topic:
Last edited by ptuomov; 09-05-2017 at 08:26 AM.