997 GT2 - RS Tuning 600PS
12-08-2009, 08:29 AM
#1
Racer
Thread Starter
Join Date: Jan 2006
Location: Melbourne, Australia
Posts: 298
Likes: 0
Received 0 Likes
on
0 Posts
997 GT2 - RS Tuning 600PS
My Tuning package arrived today 
. Refitted the ECU tonight, will install the headers, cats & airfilter on Thursday. Purchased the package via Gert @ Carnewal....great service.
. Refitted the ECU tonight, will install the headers, cats & airfilter on Thursday. Purchased the package via Gert @ Carnewal....great service.
12-08-2009, 11:35 AM
#2
Addict
Rennlist Member
Rennlist Member
Great news, thanks for sharing, fun times ahead 
You have the same Cargraphic sticker as our Canadian friend which states 811NM - the question is, is the 811NM a typo since CG state 798NM in their sales literature ?
You have the same Cargraphic sticker as our Canadian friend which states 811NM - the question is, is the 811NM a typo since CG state 798NM in their sales literature ?
12-09-2009, 07:50 AM
#7
Racer
Thread Starter
Join Date: Jan 2006
Location: Melbourne, Australia
Posts: 298
Likes: 0
Received 0 Likes
on
0 Posts
Well a little pissed off at present. Drove the car last night after fitting the ECU. Several errors when I started the car. Thought I would clear them tomorrow when I fit the cats, etc at the garage. Went to start the car today. More & More errors codes PASM failure, ABS failure, TC failure, Telling me to depress clutch (but clutch is already depressed)….car will not start. Went to recheck the connections on the ECU. All connections 100% OK. But the ECU is very very HOT. Too hot to touch. Disconnected battery again… ECU cools off after 5 minutes, reconnect it gets HOT again. Awaiting response from Cargraphic / RS Tuning.
In the meantime….is it possible for me to order a duplicate (original) ECU from Porsche ?
In the meantime….is it possible for me to order a duplicate (original) ECU from Porsche ?
Trending Topics
12-09-2009, 08:18 AM
#8
Addict
Rennlist Member
Rennlist Member
Well a little pissed off at present. Drove the car last night after fitting the ECU. Several errors when I started the car. Thought I would clear them tomorrow when I fit the cats, etc at the garage. Went to start the car today. More & More errors codes PASM failure, ABS failure, TC failure, Telling me to depress clutch (but clutch is already depressed)….car will not start. Went to recheck the connections on the ECU. All connections 100% OK. But the ECU is very very HOT. Too hot to touch. Disconnected battery again… ECU cools off after 5 minutes, reconnect it gets HOT again. Awaiting response from Cargraphic / RS Tuning.
In the meantime….is it possible for me to order a duplicate (original) ECU from Porsche ?
In the meantime….is it possible for me to order a duplicate (original) ECU from Porsche ?
Can you tell me the numbers and data printed on your cats, I am interested to know which units they sold you, I can compare to my 200 cell CG units.
Edit: No need I can make them out, just, Yours are the expensive race 100 cell from "HJS Motorsport" my 200 cell have "HJS Tuning" stamped on them
12-09-2009, 08:37 AM
#10
Addict
Rennlist Member
Rennlist Member
If it is not the connections something may have come loose inside, is it worth cracking it open and taking a look ?
I know once I had a similar problem with a Protomotive chipped ECU and it was a bit off loose solder inside the box.
I would take a peek and see if it is anything obvious, if it is not then you might as well ship it back direct to RS as there is something amiss big time if it is getting so hot !
I know once I had a similar problem with a Protomotive chipped ECU and it was a bit off loose solder inside the box.
I would take a peek and see if it is anything obvious, if it is not then you might as well ship it back direct to RS as there is something amiss big time if it is getting so hot !
12-09-2009, 09:00 AM
#11
Racer
Thread Starter
Join Date: Jan 2006
Location: Melbourne, Australia
Posts: 298
Likes: 0
Received 0 Likes
on
0 Posts
I would assume RS Tuning would still have my file. What's the chance of them sending me a replacement ECU ?
I just updated my Durametric...will try and get a few codes.
I just updated my Durametric...will try and get a few codes.
12-09-2009, 09:18 AM
#12
Addict
Rennlist Member
Rennlist Member
I just tried to call them for you and it switches to answer machine.....
12-09-2009, 09:33 AM
#13
Racer
Thread Starter
Join Date: Jan 2006
Location: Melbourne, Australia
Posts: 298
Likes: 0
Received 0 Likes
on
0 Posts
I am currently speaking/e-mailing via Gert (Carnewal) & Alex (Cargraphic). Not good news with the Durametric error codes "Module Failed To Initialize" .
12-09-2009, 06:52 PM
#14
Why do I feel so left out!
Rennlist Member
Rennlist Member
Spence,
On the case - once i know something I will let you know.
RS/Cargraphic are good people - I reckon they wil sort you out - makes me feel bad i gave them "they are gods" speech to you....
Simon.
On the case - once i know something I will let you know.
RS/Cargraphic are good people - I reckon they wil sort you out - makes me feel bad i gave them "they are gods" speech to you....
Simon.
12-09-2009, 07:57 PM
#15
Three Wheelin'
It will get sorted out.
sorry to hear about your problems.
It could be a defect with the computer or shipping may have damaged it.
New computers need to be program/matched to the individual car.
sorry to hear about your problems.
It could be a defect with the computer or shipping may have damaged it.
New computers need to be program/matched to the individual car.