G50/32 RS CS Gearsets
#1
Race Car
Thread Starter
G50/32 RS CS Gearsets
I posted this earlier and have a few of the gears left, at least one complete 3-6 and then some ind gears after that. Someone else needs to do this...this was the single best individual 993 mod I did, I had 8 993's so I assure You its from experience!LOL
https://rennlist.com/forums/993-forum/465548-g50-gears-fs-rs-ratios-and-g50-21-a.html
The gears are very close to the g50-21 but pretty much dead on for the g50-32 RS gears.
https://rennlist.com/forums/993-forum/465548-g50-gears-fs-rs-ratios-and-g50-21-a.html
The gears are very close to the g50-21 but pretty much dead on for the g50-32 RS gears.
#3
other than that g64 and g50 use the same gears and other internal components.
the difference between then is all at the nose where the g64s have the extra v/c
Glen is absolutely right about the regearing being one of the best things you can do for a car w/ a /20
#5
Rennlist Member
#6
Race Car
Thread Starter
The ratios I have left are :
3rd,(1) 1.41(used as a ultra short 4 usually),
4th (1) 1.24 (SuperCup ratio or G50/32 RS ratio),(1) 1.18
5th (1).93(makes a great short 6) ,(1)1.16(g50 Cup/RSR ratio short 5,or ultra short 6),
6th (3).857(These are SuperCup or G50/32 RS ratio 6th) or (1).775
In the six spd any 3 and 4 fit either 3 or 4 ,and any 5 or 6 fits either 5th or 6th.
Feel free to ping me with any questions at all.
3rd,(1) 1.41(used as a ultra short 4 usually),
4th (1) 1.24 (SuperCup ratio or G50/32 RS ratio),(1) 1.18
5th (1).93(makes a great short 6) ,(1)1.16(g50 Cup/RSR ratio short 5,or ultra short 6),
6th (3).857(These are SuperCup or G50/32 RS ratio 6th) or (1).775
In the six spd any 3 and 4 fit either 3 or 4 ,and any 5 or 6 fits either 5th or 6th.
Feel free to ping me with any questions at all.
Last edited by Glen; 12-13-2008 at 09:57 AM. Reason: Updating
Trending Topics
#8
Seared
Rennlist Member
Rennlist Member
#9
Addict
Lifetime Rennlist
Member
Lifetime Rennlist
Member
I second that recommendation! Over the years I have too bought a LOT of stuff from the Glen parts Depot including my trailer and something VERY special I'm just thankful that I'm now far away from him. He is such a bad man
#10
Rennlist Member
Thx to Glen for being a class act. He spent a generous amount of time on the phone with me tonight, not only figuring out appropriate gear ratios, but also with lots of other helpful 993 advice. He obviously has an incurable illness .
#11
#12
Drifting
What is the Est. Cost of doing this Mod? I'm sure there are many different ways of pulling this off, ie. exchange G-50 Gearbox, etc. But give me an $$ idea of the budget alternatives.
#14
Race Car
Thread Starter
The ratios I have left are :
3rd,(1) 1.41(used as a ultra short 4 usually),
4th (1) 1.24 (SuperCup ratio or G50/32 RS ratio),(1) 1.18
5th (1).93(makes a great short 6) ,(1)1.16(g50 Cup/RSR ratio short 5,or ultra short 6),
6th (3).857(These are SuperCup or G50/32 RS ratio 6th) or (1).775
In the six spd any 3 and 4 fit either 3 or 4 ,and any 5 or 6 fits either 5th or 6th.
Feel free to ping me with any questions at all.
3rd,(1) 1.41(used as a ultra short 4 usually),
4th (1) 1.24 (SuperCup ratio or G50/32 RS ratio),(1) 1.18
5th (1).93(makes a great short 6) ,(1)1.16(g50 Cup/RSR ratio short 5,or ultra short 6),
6th (3).857(These are SuperCup or G50/32 RS ratio 6th) or (1).775
In the six spd any 3 and 4 fit either 3 or 4 ,and any 5 or 6 fits either 5th or 6th.
Feel free to ping me with any questions at all.