Random 964 Picture Thread
#9932
Rennlist Member
event in carrollton, tx yesterday
The following 6 users liked this post by rsabeebe:
964Luftballoon (05-08-2022),
Laurus (05-09-2022),
Scott Dunavant (05-08-2022),
spooky69 (05-08-2022),
TomJVW (05-24-2022),
and 1 others liked this post.
#9933
My new to me 91 Turbo.
99,000kms
PTS Linen Grey Metallic over black leather
RoW from Japan, now in Victoria BC
More pics here: https://photos.app.goo.gl/EL8dcabZaqu6yg5WA
99,000kms
PTS Linen Grey Metallic over black leather
RoW from Japan, now in Victoria BC
More pics here: https://photos.app.goo.gl/EL8dcabZaqu6yg5WA
The following 8 users liked this post by _Remi:
cbracerx (05-11-2022),
dukmon (05-10-2022),
forbiddenbeat (05-23-2022),
georgej (05-10-2022),
Ken D (05-10-2022),
and 3 others liked this post.
#9935
Rennlist Member
#9936
Rennlist Member
I only had a 133 mile test run but I am 99% done with my slick top conversion and everything else conversion. The MCS is far more compliant than I expected and the car is completely transformed in every way.
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
The following 11 users liked this post by cobalt:
964Luftballoon (05-11-2022),
Brig993 (05-11-2022),
cbracerx (05-11-2022),
dukmon (05-11-2022),
heliolps2 (05-12-2022),
and 6 others liked this post.
#9937
Rennlist Member
I only had a 133 mile test run but I am 99% done with my slick top conversion and everything else conversion. The MCS is far more compliant than I expected and the car is completely transformed in every way.
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
Mr. Wolfe
The following users liked this post:
JP-"S" (05-12-2022)
#9939
Rennlist Member
#9940
Rennlist Member
random...
I only had a 133 mile test run but I am 99% done with my slick top conversion and everything else conversion. The MCS is far more compliant than I expected and the car is completely transformed in every way.
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
I wish I had 1000 Miles of canyon back roads to drive by me. Nicely done!!
#9941
Rennlist Member
I went with the 2WNR with 400/500 springs and 225 tenders. I will be playing with settings for a while . I think the compression needs adjusting in the back end and I have the sways on middle for now. I did go from a 24mm rear to an 18mm RS bar. The 24 is going on the track car. I also went with full HD rubber throughout except the hats which are tarrett. This is a driver and I didn't want to stray too far from OE. I also switched out the front end to 993 uprights and associated parts saving some nice reduction in unsprung weight. Height is RS +5mm, corner balanced. The roof and other items saved me 60 pounds mostly up high but I did install the A/C so I have to figure another 6 or 7. I used 993 intakes which raise the injectors 4mm. It could be my head and being so long since I have driven it but it feels as though I get a burst of added power at WOT. Would need to dyno it to know for sure if it changed anything.
#9942
The following 8 users liked this post by TomJVW:
964Luftballoon (05-16-2022),
delanobe (05-14-2022),
FlatSix911 (05-14-2022),
Laurus (05-14-2022),
Ray S (05-19-2022),
and 3 others liked this post.
#9943
Picked this up a few weeks ago and been going through it. It's a 90 c2 built by Sunburst Japan. Was raced there and imported here some years ago by Mitsuwa. Built 3.6 by Promodet w/ PMO carbs and MSD ignition, all fiberglass RSR type wide body work, coilovers, minimal interior, no heat/air, lots of RS parts I'm told. I love it, and looking forward to putting lots of miles on it.
The following 5 users liked this post by s65e90:
964Luftballoon (05-16-2022),
JP-"S" (06-06-2022),
RAVEN928 (05-18-2022),
Ray S (05-19-2022),
TomJVW (05-16-2022)
#9944
Three Wheelin'
Picked this up a few weeks ago and been going through it. It's a 90 c2 built by Sunburst Japan. Was raced there and imported here some years ago by Mitsuwa. Built 3.6 by Promodet w/ PMO carbs and MSD ignition, all fiberglass RSR type wide body work, coilovers, minimal interior, no heat/air, lots of RS parts I'm told. I love it, and looking forward to putting lots of miles on it.
Here's a slightly less aggressive C4, that went the other way - US to Japan:
More here.
See ya!
#9945
The following 6 users liked this post by s65e90:
FlatSix911 (05-22-2022),
JP-"S" (06-06-2022),
RAVEN928 (05-25-2022),
Scott Dunavant (05-22-2022),
TomJVW (05-24-2022),
and 1 others liked this post.