TonyG > New Race Car Build Thread
#1366
Pro
#1368
Rennlist Junkie Forever
Thread Starter
Trans is in.
Steering wheel getting done. Look at the shifter ma!
Dropping the GM ecu. Going AEM with dual wide band, cockpit adjustable traction control and DBW throttle (much cleaner than using a blipper)... and more. Always more....
Will be ready for testing by the end of next week.
TonyG
...
...
...
Steering wheel getting done. Look at the shifter ma!
Dropping the GM ecu. Going AEM with dual wide band, cockpit adjustable traction control and DBW throttle (much cleaner than using a blipper)... and more. Always more....
Will be ready for testing by the end of next week.
TonyG
...
...
...
#1370
Rennlist Member
Glad to see Archsoft is going so well!! ;-)
#1372
Rennlist Junkie Forever
Thread Starter
Update...
Wiring almost done.
Went from GM computer to Motec, the Geartronics computer for the transmission (both talk over the can bus), 102mm drive by wire throttle (for throttle blipping and traction control), new intake, new headers and complete exhaust, new lifters and valve springs, rear blown difusser, and more....
LOTS of wiring involved.
TonyG
...
...
...
Wiring almost done.
Went from GM computer to Motec, the Geartronics computer for the transmission (both talk over the can bus), 102mm drive by wire throttle (for throttle blipping and traction control), new intake, new headers and complete exhaust, new lifters and valve springs, rear blown difusser, and more....
LOTS of wiring involved.
TonyG
...
...
...
#1375
Rennlist Member
This thing is going to be fairly rapid...
#1376
Rennlist Member
=TonyG;13096444]Here's the update....
....
Anyway, broke the clutch and bell housing in the last race.....
....
Anyway, broke the clutch and bell housing in the last race.....
Just lost my C5 BH last weekend.
I am going to go with the QuickTime SFI rated BH with the integral adaptor for the 944 BH. It's amazing they make a custom BH for a small slice of a small market. Probably overkill for my 400 RWHP, but peace of mind should a clutch fail.
Gorgeous build on yours, and good luck with the new box!
Last edited by Sterling Doc; 05-27-2016 at 10:27 AM.
#1378
Rennlist Junkie Forever
Thread Starter
That's from over revving the engine. These full sized pressure plates start to come apart at high rpms.
You can use what ever bell housing you want, it won't fix that issue.
A small twin disk will however.. :-)
TonyG
You can use what ever bell housing you want, it won't fix that issue.
A small twin disk will however.. :-)
TonyG
---------------------------------------------------------------------------------------------------------------------------------
Just lost my C5 BH last weekend.
I am going to go with the QuickTime SFI rated BH with the integral adaptor for the 944 BH. It's amazing they make a custom BH for a small slice of a small market. Probably overkill for my 400 RWHP, but peace of mind should a clutch fail.
Gorgeous build on yours, and good luck with the new box!
Just lost my C5 BH last weekend.
I am going to go with the QuickTime SFI rated BH with the integral adaptor for the 944 BH. It's amazing they make a custom BH for a small slice of a small market. Probably overkill for my 400 RWHP, but peace of mind should a clutch fail.
Gorgeous build on yours, and good luck with the new box!
#1379
Rennlist Junkie Forever
Thread Starter
I've been dealing with both. The Geartronics software is more developed. So I decided to use their hardware and software.
It communicates with the Motec over the can bus.
Also went to DBW for throttle blipping and traction control.
The game has changed...
TonyG
#1380
Rennlist Junkie Forever
Thread Starter