OB Center Console Trim Surround Project
#61
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I'd better sell off my stash of good ones while I still can.
#65
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Hi Guys, sorry to jump in. I was following you for a while. I finally found a solution.
I am able to have part 928 552 047 04 (with 3 holes) reproduced by a friend of mine who owns a Industrial 3D Printing Facility. Actually it will be molded. Final result has therefore the same 'vynil' aspect as the original part. The new part keeps flexibility to fit although minor adjustments maybe required on the back.
The challenge is : get at least 10 persons intersted in purchasing such a copy to get to 245 € per part (excluding shipping).
If you are intereted in getting one, please contact me through the forum.
I hope this help
Jerome
I am able to have part 928 552 047 04 (with 3 holes) reproduced by a friend of mine who owns a Industrial 3D Printing Facility. Actually it will be molded. Final result has therefore the same 'vynil' aspect as the original part. The new part keeps flexibility to fit although minor adjustments maybe required on the back.
The challenge is : get at least 10 persons intersted in purchasing such a copy to get to 245 € per part (excluding shipping).
If you are intereted in getting one, please contact me through the forum.
I hope this help
Jerome
#66
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Sounds like another Potdog here. Sure I haven't finished my solution to this yet so anyone is free to swoop in and try their own solution.
If you need one of these now go ahead and buy his at $300 USD a piece. I will say though that mine will be considerably less than $200 and shipping will be a lot cheaper for anyone in North America. I am doing all of the engineering and manufacturing myself and don't have to pay others for their time. I will have these ready this Summer.
Nate
If you need one of these now go ahead and buy his at $300 USD a piece. I will say though that mine will be considerably less than $200 and shipping will be a lot cheaper for anyone in North America. I am doing all of the engineering and manufacturing myself and don't have to pay others for their time. I will have these ready this Summer.
Nate
#67
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Sounds very interesting. Thanx for offering this.
Where are you located?
I am from Germany and would opt for two pieces of the 3hole version.
Any chance of showing us a sample before I/we sign up for it?
Where are you located?
I am from Germany and would opt for two pieces of the 3hole version.
Any chance of showing us a sample before I/we sign up for it?
#68
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
https://rennlist.com/forums/showpost...2&postcount=17
You must be a paid member to advertise parts for sale on Rennlist.
Last edited by GT6ixer; 04-24-2018 at 07:09 PM. Reason: removed ad info for the potential removal of non-member for sale posting
#69
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Agreed Nate. No way do I trust a guy who just jumped in out of nowhere. Hmm, maybe I'll send him my money first![hiha](https://rennlist.com/forums/graemlins/roflmao.gif)
Jerome - join up and post some info about yourself, establish some cred before hoping in to huck stuff, and it is very bad form to do so on another's thread
![hiha](https://rennlist.com/forums/graemlins/roflmao.gif)
Jerome - join up and post some info about yourself, establish some cred before hoping in to huck stuff, and it is very bad form to do so on another's thread
![manual](https://rennlist.com/forums/graemlins/rtfm.gif)
#70
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I am sticking with you Nate - ignore the other guy and keep up the good work.
__________________
![](https://cdn.shopify.com/s/files/1/1694/8685/files/928sRus_rennlist.png?v=1621798567)
Does it have the "Do It Yourself" manual transmission, or the superior "Fully Equipped by Porsche" Automatic Transmission?
George Layton March 2014
928 Owners are ".....a secret sect of quietly assured Porsche pragmatists who in near anonymity appreciate the prodigious, easy going prowess of the 928."![thumbsup](https://rennlist.com/forums/graemlins/bigok.gif)
![](https://cdn.shopify.com/s/files/1/1694/8685/files/928sRus_rennlist.png?v=1621798567)
Does it have the "Do It Yourself" manual transmission, or the superior "Fully Equipped by Porsche" Automatic Transmission?
![thumbsup](https://rennlist.com/forums/graemlins/bigok.gif)
928 Owners are ".....a secret sect of quietly assured Porsche pragmatists who in near anonymity appreciate the prodigious, easy going prowess of the 928."
![thumbsup](https://rennlist.com/forums/graemlins/bigok.gif)
#71
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Hi Guys, You are right, wrong start and applologies.
So to present myself : Actually I am the founder of www.matching-numbers.net, a sport cars owners community in Belgium, switzerland and France. You can also find us on facebook https://www.facebook.com/MatchNumbers/
I personnaly own a few cars amongst which et few Porsches (924 Turbo, 912 Targa and ... a 928 from 1979).
The 928 is mint except ... that part we are talking about. I was following your forum for mors that a year and hoping a solution. I recently have had a new member in my community who owns a major 3D Printing factory in Paris.
I thought your project was dead so ...
As I start to better understand the cmplexity of that part, don't forget to consider that a 3D printing will give you a part that will have a raw aspect which will need to be covered and that the part flexiblity has a chance to be too rigid. Molding will enable us to have the right aspect + the right flexiblity to easily clip the part.
That's it. I just have had the chance to meet someone who has a strong experience on such a topic (building parts for plane fighters, etc) and hope we could team up with people having a need to get things solved by splitting production costs (ie : not making money).
Cheers,
Jerome
PS : what is 'PotDog' ?
Jerome
So to present myself : Actually I am the founder of www.matching-numbers.net, a sport cars owners community in Belgium, switzerland and France. You can also find us on facebook https://www.facebook.com/MatchNumbers/
I personnaly own a few cars amongst which et few Porsches (924 Turbo, 912 Targa and ... a 928 from 1979).
The 928 is mint except ... that part we are talking about. I was following your forum for mors that a year and hoping a solution. I recently have had a new member in my community who owns a major 3D Printing factory in Paris.
I thought your project was dead so ...
As I start to better understand the cmplexity of that part, don't forget to consider that a 3D printing will give you a part that will have a raw aspect which will need to be covered and that the part flexiblity has a chance to be too rigid. Molding will enable us to have the right aspect + the right flexiblity to easily clip the part.
That's it. I just have had the chance to meet someone who has a strong experience on such a topic (building parts for plane fighters, etc) and hope we could team up with people having a need to get things solved by splitting production costs (ie : not making money).
Cheers,
Jerome
PS : what is 'PotDog' ?
Jerome
#72
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I'd love to have a new surround. I have a one hole in good condition, but it's starting to show its age, and I'd love to get a 3 hole and put USB adapters in. However, €245 is simply not going to happen. I understand that there's a set up fee associated with the molding, but: yeesh.
#73
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Nate: It just occurred to me that you might want to consider a version with no ashtray opening, just a flat panel that could be opened up by the purchaser for gauges and whatnot.
#74
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Bump...
Any progress?
Any progress?