Repairs and changes you have to do before SITM 2011.
#46
Rest in Peace
Rennlist Member
Rennlist Member
Thread Starter
Join Date: May 2006
Location: Bird lover in Sharpsburg
Posts: 9,903
Likes: 0
Received 2 Likes
on
2 Posts
It is past toast, reminds me of a Pizza I left on the BGE at 950 degrees for a few minutes.
#49
Administrator - "Tyson"
Lifetime Rennlist
Member
Lifetime Rennlist
Member
#50
Rennlist Member
my list has grown since my first post in this thread....
wp/tb?cam gears were added, and while i am there, MM OPG are getting done.
I have the X pipe to install and the wideband o2 for some future sharktuning......
X pipe is here but wideband is not...
i also found play in passenger wheel bearing so that will be replaced next week...
I doubt i will have the hatch repainted by then, but oh well.....
wp/tb?cam gears were added, and while i am there, MM OPG are getting done.
I have the X pipe to install and the wideband o2 for some future sharktuning......
X pipe is here but wideband is not...
i also found play in passenger wheel bearing so that will be replaced next week...
I doubt i will have the hatch repainted by then, but oh well.....
#51
Rennlist Member
Haha my list is longer too. Putting in the clutch slave and master. Yes this is as much of a pain that everyone says.
Then I need to bolt up my motor mounts and off we go.
With no AC - pretty much a given, the wife's car ate that cash up with a 13year old radiator failure.
Then I need to bolt up my motor mounts and off we go.
With no AC - pretty much a given, the wife's car ate that cash up with a 13year old radiator failure.
#52
Rennlist Member
Well, I had to replace a steering boot, that turned into a tie rod. But finally buttoned that up and was driving to work today (need to settle suspension for an alignment), and the window fell into the door. But besides that, I think I am down to an oil change and hit the road. At least I hope that is what's left...
#53
Rennlist Member
#54
Rennlist Member
Master cylinder in!
New motor mounts "mounted".
Cross member is back in place but not bolted to the frame, rack and other associated bits not yet installed... Tomorrow I will continue!
New motor mounts "mounted".
Cross member is back in place but not bolted to the frame, rack and other associated bits not yet installed... Tomorrow I will continue!
#56
Rest in Peace
Rennlist Member
Rennlist Member
Thread Starter
Join Date: May 2006
Location: Bird lover in Sharpsburg
Posts: 9,903
Likes: 0
Received 2 Likes
on
2 Posts
Well, my timing belt is done, some fuel lines installed, some replated parts installed.
Got what I think is the rest of the parts for a customers 928, one should go out Monday, then the GT should be getting pretty much done on the engine early next week.
Few other issues to deal with on it, but it looks good right now.
I still have to install the wideband on mine, do the rest of the fuel hoses, and the Carputer install, plus sharktune.
So I have a really full couple of weeks.
Got what I think is the rest of the parts for a customers 928, one should go out Monday, then the GT should be getting pretty much done on the engine early next week.
Few other issues to deal with on it, but it looks good right now.
I still have to install the wideband on mine, do the rest of the fuel hoses, and the Carputer install, plus sharktune.
So I have a really full couple of weeks.
#57
Rennlist Member
Join Date: Feb 2008
Location: Lillington, NC
Posts: 2,742
Likes: 0
Received 0 Likes
on
0 Posts
-getting wheels powder coated
-mount new PS2's
-get nose repainted
-check alignment
-change oil
-get tint on driverside replaced
-install new chin spoiler and wheel liners
-mount new PS2's
-get nose repainted
-check alignment
-change oil
-get tint on driverside replaced
-install new chin spoiler and wheel liners