Artist turned mechanic...
#17
Rennlist Member
The following users liked this post:
Daniel5691 (03-10-2020)
#18
Rennlist Member
The following 3 users liked this post by Kevin in Atlanta:
#19
Rennlist Member
Kevin in Atlanta - I'm interested in two of these, when are they ready for primetime?
#20
Rennlist Member
The following users liked this post:
Daniel5691 (03-10-2020)
#21
Nice product Kevin and Kevin!
Wish they were made years ago...
Wish they were made years ago...
#23
Rennlist Member
That's a perfect solution for those that already own the 928Intl version.
#24
Nordschleife Master
Welcome (I guess). And good luck.
If you want to see what you are in for, Dwayne, of Dwayne's Garage has a wonderful write up on the Motor Mounts (MMs). Once you get it apart, the Oil Pan Gasket (OPG) is right there.
There's a link to Dwayne's site in the "New Visitor" sticky.
I will agree that this is not a good 'first dip' into the "Care and Feeding of a 928" pond.
But it's not all that hard.
You have to pretty much take apart the entire bottom of the front end of the car. Sway bar, steering rack, Lower Control Arms (LCA) and cross member have to come off. Alternator & power steering pump have to come off the front of the motor. The motor has to be supported from the top (Dwayne has a really good setup made from 4x4 beams for that). The pan is held on by approximately 1,357,924 bolts (really like 20, but it seems like a lot more). Some of them are 'challenging' to get to.
OTOH, none of it is terribly difficult, just involved and intimidating. There are a few potential pitfalls, getting the crossmember bolts back in is one, but Dwayne covers it well.
Getting the car up as high as possible is critical. Many of us use Ken's LiftBars. They make getting the car up & down a lot easier, and give an extra couple inches on the jackstands. A lift is best, but not everyone has one of those.
I will disagree with Ake about making your own pan gasket. That sort of thing is not for a beginner. Greg Brown makes & sells a very nice one. Far superior to the original cork, yet it isn't thick like the silicone one, so bolts can be properly tightened. He had a thread on it a month or so ago when he introduced it.
If you want to see what you are in for, Dwayne, of Dwayne's Garage has a wonderful write up on the Motor Mounts (MMs). Once you get it apart, the Oil Pan Gasket (OPG) is right there.
There's a link to Dwayne's site in the "New Visitor" sticky.
I will agree that this is not a good 'first dip' into the "Care and Feeding of a 928" pond.
But it's not all that hard.
You have to pretty much take apart the entire bottom of the front end of the car. Sway bar, steering rack, Lower Control Arms (LCA) and cross member have to come off. Alternator & power steering pump have to come off the front of the motor. The motor has to be supported from the top (Dwayne has a really good setup made from 4x4 beams for that). The pan is held on by approximately 1,357,924 bolts (really like 20, but it seems like a lot more). Some of them are 'challenging' to get to.
OTOH, none of it is terribly difficult, just involved and intimidating. There are a few potential pitfalls, getting the crossmember bolts back in is one, but Dwayne covers it well.
Getting the car up as high as possible is critical. Many of us use Ken's LiftBars. They make getting the car up & down a lot easier, and give an extra couple inches on the jackstands. A lift is best, but not everyone has one of those.
I will disagree with Ake about making your own pan gasket. That sort of thing is not for a beginner. Greg Brown makes & sells a very nice one. Far superior to the original cork, yet it isn't thick like the silicone one, so bolts can be properly tightened. He had a thread on it a month or so ago when he introduced it.
#25
It would have been nice if they made the belly pans with access holes to change the oil and filter
as it is an oil change on an S4 is a time consuming adventure not to mention all the different kinds of fasteners that are put back in
by creative mechanics
At this point removing the pans and leaving them off while you contemplating service needs will be prudent
just secure the front spoiler lower edge so it stays up otherwise you can catch it backing out of a driveway
as it is an oil change on an S4 is a time consuming adventure not to mention all the different kinds of fasteners that are put back in
by creative mechanics
At this point removing the pans and leaving them off while you contemplating service needs will be prudent
just secure the front spoiler lower edge so it stays up otherwise you can catch it backing out of a driveway
#26
Rennlist Member
#27
Addict
Rennlist Member
Rennlist Member
Join Date: Oct 2003
Location: Gone. On the Open Road
Posts: 16,521
Received 1,664 Likes
on
1,079 Posts
#28
Rennlist Member
Join Date: Feb 2011
Location: Mostly in my workshop located in Sweden.
Posts: 2,235
Received 467 Likes
on
250 Posts
Welcome (I guess). And good luck.
If you want to see what you are in for, Dwayne, of Dwayne's Garage has a wonderful write up on the Motor Mounts (MMs). Once you get it apart, the Oil Pan Gasket (OPG) is right there.
There's a link to Dwayne's site in the "New Visitor" sticky.
I will agree that this is not a good 'first dip' into the "Care and Feeding of a 928" pond.
But it's not all that hard.
You have to pretty much take apart the entire bottom of the front end of the car. Sway bar, steering rack, Lower Control Arms (LCA) and cross member have to come off. Alternator & power steering pump have to come off the front of the motor. The motor has to be supported from the top (Dwayne has a really good setup made from 4x4 beams for that). The pan is held on by approximately 1,357,924 bolts (really like 20, but it seems like a lot more). Some of them are 'challenging' to get to.
OTOH, none of it is terribly difficult, just involved and intimidating. There are a few potential pitfalls, getting the crossmember bolts back in is one, but Dwayne covers it well.
Getting the car up as high as possible is critical. Many of us use Ken's LiftBars. They make getting the car up & down a lot easier, and give an extra couple inches on the jackstands. A lift is best, but not everyone has one of those.
I will disagree with Ake about making your own pan gasket. That sort of thing is not for a beginner. Greg Brown makes & sells a very nice one. Far superior to the original cork, yet it isn't thick like the silicone one, so bolts can be properly tightened. He had a thread on it a month or so ago when he introduced it.
If you want to see what you are in for, Dwayne, of Dwayne's Garage has a wonderful write up on the Motor Mounts (MMs). Once you get it apart, the Oil Pan Gasket (OPG) is right there.
There's a link to Dwayne's site in the "New Visitor" sticky.
I will agree that this is not a good 'first dip' into the "Care and Feeding of a 928" pond.
But it's not all that hard.
You have to pretty much take apart the entire bottom of the front end of the car. Sway bar, steering rack, Lower Control Arms (LCA) and cross member have to come off. Alternator & power steering pump have to come off the front of the motor. The motor has to be supported from the top (Dwayne has a really good setup made from 4x4 beams for that). The pan is held on by approximately 1,357,924 bolts (really like 20, but it seems like a lot more). Some of them are 'challenging' to get to.
OTOH, none of it is terribly difficult, just involved and intimidating. There are a few potential pitfalls, getting the crossmember bolts back in is one, but Dwayne covers it well.
Getting the car up as high as possible is critical. Many of us use Ken's LiftBars. They make getting the car up & down a lot easier, and give an extra couple inches on the jackstands. A lift is best, but not everyone has one of those.
I will disagree with Ake about making your own pan gasket. That sort of thing is not for a beginner. Greg Brown makes & sells a very nice one. Far superior to the original cork, yet it isn't thick like the silicone one, so bolts can be properly tightened. He had a thread on it a month or so ago when he introduced it.
Wisconsin Joe, when you have gone through all the cumbersome extensive work to be able to remove the oil pan, the manufacturing of your own oil pan gasket is the most
simplest thing to do but if you consider that Mr. Brown needs the business to earn some money selling a gasket I have nothing against that. We who live in the old world do not have a Mr. Brown to turn to so we have to manage on our own. To pay eighty dollars for shipping for a gasket that will arrive after more than two weeks and furthermore additional costs for customs duty and import sales tax does not make sense.
Åke
#29
#30
Rennlist Member