xsboost90

So the brother in laws car finally bit it...again. The second motor we installed in this car now has either floated a valve or burnt one-possibly a rod bearing but i doubt it. The tub was slightly twisted from a bad wreck to begin with so no futher cash will be laid out to save this car. However the list of goodies is there and will be sold off to pay for hopefully a nicer n/a here soon. Here is the list...
*86 n/a

motor parts- motor is an 87 w/ auto tensioner etc..

-short block- i'll take a look when its out...junk-coffie table..
-head -one bent valve-$50-intake sprayed black- $30
-throttle body- $15
-stock non-painted intake- $30
-rad fans -pm for individual fans/motors price*
-
-misc fuses/relays - pm me- $10 per relay
-stock airbox-spray canned on top for some reason- make offer w/ k$n filter
-j-boot in fair shape- $10
-Stock clutch parts - make offer
-"ok" shape disc is used obviously
-bellhousing-$40

-aos- $10-oil pan- i have three- one was steam cleaned- $25 each

drivetrain parts

-N/A open diff trans drives great - shifts great- $350

-
-968 factory swaybars -NOT mo30 26.5mm front and 16mm rear $125 both or $75 each*

body

-front n/a lower valance w/ fogs- $100 paint chipped but no cracks

-rear bumper eurethane endcaps $15ea- red
-flip up headlight parts/motors/brakets/buckets/lights/linkage- make offers or $75 for all parts involved working w/ motor etc..

-n/a brake parts ....-calipers $20 both front and $20 both rear w/ good pads on front-
-spindles $20
-hubs $20
-
-windows and quarter windows $10 each
rear side panels- $20
-rear hatch $75 w/ wing not separated!
-sunroof-red- w/ seal - $40
-sunroof liner- $20
-spare tire on steel rim - good shape $25
-jack no handle - offers
-pretty nice tool kit- $25
-turn signal column stalk-no cruise- $40 works
-plate brakets- $10**
-center console w/o lid- $35
*black-dash trim- $10 each pm me*

-sun visors- $10 each- $15 both black and not falling down or sagging
-sunvisor headliner trim - $15
-rubber door and hatch seals- $10 any seal pm me for specifics
-exhaust ** cast manifolds -$30**
-gas tank lid- $10
-gas cap- $10

added!!-

ebrake handle- nice! black- $25
-console cubby-small hole drilled in bottom for a wire- $10
-console ash tray- $10
-switches from center console- $5 each
-hood latch-$5
-master cylinder- $15
-NEW oil pressure sender $35
-dash-cracked and black- offers

ADDED 7/3/08

set of FIVE 16" early offset turbo wheels- three 7x16" front wheels and two 16x8" rears (one of which has a nice sized curb in it) fixable- held air after the incident and spun straight but has a nasty curb in the outer lip. $350 all five w/ used track tires

vented 931-n/a nosepan- red- w/ vents- needs alittle tlc but overall could be bolted on and rocked for awhile no problems- i painted it a year ago and did some body work but it bumped another car "somehow" and i had to hammer the center between the vents alittle so its not perfect- $200

Wipeout

Hey dan, is there some sort of connector/strut/something that holds the front fender in front of the tire in place on the passenger side? My fender doesn't have a support on that side, but I am pretty sure my driver's side has something there. I'd be interested in that piece, if it were there.

2BWise

PM sent

Darwantae951

Damn, you guys did awesome on that engine, sorry to hear that it went so soon.

Strike-Force

Will you be pulling body panels? Interested in passenger rear quarter panel if you are.

Spidey944

Hey Danno,

Interested in the Blue Magnacores, and also some spark plug wire holders if you have them in good shape. Also what shape is the hatch carpet in?? Thanks.

Microrws

Hi Dan,
Sorry for the lost but I will like the gauge cluster-$50 PM sent

Russell

El Commandante

Pm sent. Oh, and by the way, do you happen to have an alternator or cruise control servo? Thanks

SamGrant951

That sucks, sorry to hear it...

rudevr6

dibbs on the plug wires and front left quarter! hows about shipping to 16127, grove city pa? what kind of suspension (re: struts springs etc.) i may be needing these as well.

tk's944

Do you have the driver side fender molding?

F18Rep

Can I get in line for the rear bumper pads? Bruce

flosho

I would like BOTH front fenders, if they are both available, please send pictures and shipping would be to 54701(wisconsin). flosho924@gmail.com


Thanks
Jason

Dinman_UT

Do you have some pics of the interior. i.e. condition of HVAC controls, sunvisors, and shift assembly? Also, what extra lights are wired into the tail light assembly? Also, I will probably be needing some rear body panels, but will probably have to wait for insurance check

ArcticSteve

PM sent