CS steering wheel
#16
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by Boeing 717
Thanks Jay I have read that a few times but don't see anything about just installing the resistor. Do you still have to cut wires and stuff if your installing the resistor?
#19
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by thomasmryan
I assume the battery should be disconnected for a half an hour or so and the key should not be inserted during the process as to not trigger the airbag module trouble codes
![hiha](https://rennlist.com/forums/graemlins/roflmao.gif)
#22
Drifting
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
Seriously though, I like the red stitching, don't care for he porsche letters too much. Looks to be the same otherwise.
I would not sweat it
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#24
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
#25
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
That is the way the 964 Turbo S steeringwheel looked like.
The 1991 951 I owned had that steering wheel from factory. IMO the nicest wheel from Porsche.
The 1991 951 I owned had that steering wheel from factory. IMO the nicest wheel from Porsche.
#26
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Here is a bad screenshot pic I took of the ad when my old -91 recently sold on in Germany. You can see the wheel.
That car had a spec I have never seen before. It is cobolt blue with full leather interior in blue and that is with leather dash, centerconsole, doorcards, rear sides etc etc in leather. It also has wood interior, klangpaket with 10 cd changer in the boot. 17" cup 1 etc from factory. It was also built in the Stuttgart plant which only the very late -91 cars was all other at the Audi neckarsulm plant. Very rare spec and I loved that steering wheel. My father in law bought the car and sadly drove it into a ditch. It was bent really bad and was fixed up and sold again by the company that bought it from the insurance company and later ended up in Germany and sold recently.
That car had a spec I have never seen before. It is cobolt blue with full leather interior in blue and that is with leather dash, centerconsole, doorcards, rear sides etc etc in leather. It also has wood interior, klangpaket with 10 cd changer in the boot. 17" cup 1 etc from factory. It was also built in the Stuttgart plant which only the very late -91 cars was all other at the Audi neckarsulm plant. Very rare spec and I loved that steering wheel. My father in law bought the car and sadly drove it into a ditch. It was bent really bad and was fixed up and sold again by the company that bought it from the insurance company and later ended up in Germany and sold recently.
Last edited by PF; 12-18-2016 at 04:06 PM.
#27
Registered User
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Guys I put the new steering wheel on and plugged the orange connector with the resistor that Raj sent me. I have an airbag light though when I started the car. Any ideas?
#28
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by Boeing 717
Guys I put the new steering wheel on and plugged the orange connector with the resistor that Raj sent me. I have an airbag light though when I started the car. Any ideas?
#29
Registered User
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by RajDatta
You will need to clear the code via durametric or a similar diagnostic tool.
Thanks
Merry Christmas!!!