Just blew out Vanagon CV joint!
#1
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Based on a lot of the positive feedback I've read, about a month ago we installed new Empi Vanagon axle assemblies in our lightly modded '86 951. This AM, I gave it full throttle/boost in first and it blew out the drivers inner CV joint. I thought that maybe I had not greased them well enough when I installed them. However, when I removed the failed CV joint, the inner race shows signs of deforming at the edges, which allowed the ***** to escape (see pic). There were no signs of excessive heat, burnt or blueish marks, which I would expect to see if it was lack of lubrication that caused he failure. If it was just lack of grease, I would consider getting another Empi axle and greasing the hell out of it. But if it is structural weakness, obviously I shouldn't get another one. If that's the case, I should probably replace the other axle with something stronger. I'd welcome any opinions.
Thanks.
Roger
Thanks.
Roger
#2
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I think I answered my own question. I compared the inner race/carrier on the Empi Vanagon axle with one of the OE ones it replaced. The OE is clearly larger (2mm larger in outside diameter, on the right below). I get the feeling I should probably bite the bullet and get OE type axles/joints.
#5
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Same thing happen to the EMPI CV axles that I used on my track car. The CVs lasted two events, with a solid tranny mount. Switched back to OEM and all is good again.
#6
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
#7
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Yes, a must really if your car is modded for more power. The failure is caused by the tranny swinging. My EMPI's have held up to drag racing at very high power levels.
Trending Topics
#8
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Roger
#10
#12
Rennlist Member
#13
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Another Empi is on it's way. I'd like to think if these can hold up to the kind of power that Shawn is putting through them, they certainly should be able to withstand what we're putting through them. With a 2.5L at 15lbs boost, I suspect we aren't any more than 260 lb/ft at the wheels. I'll pull the tranny mount off tonight and fill it with 3M window weld. hopefully that will solve the problem.
First AutoX is the end of April. Wish me luck!
Roger
First AutoX is the end of April. Wish me luck!
Roger
#14
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Do you happen to know the CV joint part number of the one that just broke? Mine are going strong with plenty more power than your car, though I don't have very many miles on them yet and installed a semi-solid transaxle mount at the same time.
#15
Racer
Thread Starter
Join Date: Aug 2003
Location: Chicago
Posts: 259
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Roger