Rennlist - Porsche Discussion Forums - View Profile: Dougs951S

Notices

Dougs951S Dougs951S is offline

Super User

About Me

  • About Dougs951S
    Biography
    87 Nautic blue metallic Turbocharged S- big turbo, big FMIC, megasquirt with ford EDIS wasted spark, E85, coilovers, too many other mods to list, pretty quick and getting quicker
    Location
    Austin TX, drinking beer in the garage
    Gender
    Male

Statistics

Total Posts
Albums
Visitor Messages
General Information
  • Last Activity: 03-05-2019 02:06 AM
  • Join Date: 03-04-2012

Friends

Showing Friends 1 to 8 of 8

Visitor Messages

Showing Visitor Messages 1 to 10 of 11
  1. 07-22-2018 10:57 AM
    Hi Doug,

    I have recently caused damage to my DME by shorting an injector lead. Do you think that
    I have damaged the injector by doing so? I have found a bad Transistor, and it appears that
    unless the IC is junk, I may be able to repair the DME. I did have the car "on" quite a while attempting to
    start it before realizing my error, and was unsure if that would hurt an injector.

    Best,
    Giltgy
  2. 03-07-2018 03:37 PM
    Hey there, Doug!

    I have some questions about Megasquirting an '83 ROW 944 and was wondering if you could give me a shout sometime!

    Thanks,

    Chris
  3. 07-04-2017 06:28 AM
    Hello Doug,
    I'm not sure if you visit the forum these days, but I'd appreciate if you could chip in and help me solve my ECU mystery! )
    https://rennlist.com/forums/general-...l#post14298088

    Thank you!
  4. vetter59
    08-21-2016 05:47 PM
    Hi Doug, I actually have 3 gouged/scratched blocks already. I talked to several weeks ago about '88 N/A pistons a few weeks back for the same car, which I believe I will be able to save and re-use by sending them to Calico Coatings, and having them re-coat piston skirts with CT-3 dry film lubricant.
    So are you saying that I am better off having my original block re-done? US Chrome in Wisconsin will put in new Alusil liners for about $945 not including shipping. Re-coating pistons about $250. 2] option would be to put steel liners, and wossner or chevy piston /ring set. Then Gaskets and bearings, rings, seals ect will probably have about $1700-1800 in short block by time I'm finished. 3] Found a low miles '87 with 77k was pristine before it was rolled, engine still in car, could hear it run before they take it out for $840.
    So I know third option the cheapest, but it would have a little less HP, but also only want to do it once! which way would you go with this?
  5. USairman
    07-18-2016 09:59 AM
    Hey Doug, how much for the head?
  6. 11-15-2015 10:41 PM
    Doug. Yes I can use the 2 piece rear undercar spoiler. Headed out of town will be touch. Chuck
  7. 11-10-2015 09:32 PM
    Hello Doug,

    I have been reading through your megasquirt project posts and just want to say they have been extremely helpful. I myself am going a different way than both you and michael by using a DIY MS3 kit that I am wiring into an extra DME I have, similar to your install. I plan to fit the entire MS3 module into the DME and wire the DB37 directly to the desoldered DME conn. I am about to put it in the case and starting to wire everything, but I have some questions. Any chance you might be willing to chat about my project sometime and offer a bit of insight. I kinda jumped right into the deep end and while i have a very firm grasp on what I am doing I still have some questions as to how you wired your microsquirt module directly into the existing wiring harness. If you have some time to chat, let me know, I would really enjoy picking your brain regarding my project. Thanks again.

    Bryan G.
  8. 03-18-2015 04:20 AM
    Hello Doug, my name is Neal and I just acquired a 1984 944 auto and was looking through the internets for ideas for it( fix it, motor swap, part it out). I have been reading your posts here on RL and realized you were in Austin( so am I ) Was curious if I might check out what you have been doing to your Stuttgart Stallions. PM me or email me at [email protected] and let me know if you would be willing to come check out my 944 and give me your opinion. Thanks, Neal
  9. 12-31-2014 12:41 PM
    Hi a saw that you are selling a bunch of 944 stuff.. i have a 944 s2 and am renovating it so i might need some stuff you see.. =) Im intressted in giving the car Ac, so all you Ac need stuff would be awesome and inside the car i have a cup of things in need of changing like the dashboard plastic all the way to the fron passanger side and stuff.. do you have those kinda things? PLz get back to me at [email protected].. i can send you pictures of the stuff im in need of.. its a bit of stuff actually!! =D Very best /D
  10. odonnell
    01-24-2014 11:12 PM
    BRING BACK THE REAL TYRONE

Contact Us - About Us - Advertising - Cookie Policy - Privacy Statement - Terms of Service

© 2019 MH Sub I, LLC dba Internet Brands

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.