Shaping up a new-to-me 07 GT3
#1
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I bought this 07 GT3 from a Chevy dealer in Albany, NY back in March. This car was pretty rough around the edges(its all can afford on a grease monkey's salary
). The dealer left the key ON in the ignition and drained the battery dead in the showroom. The previous owner spent good money on mods but just didn't turned out too well. The good news is the handling was so bad, even at legal highway speed, I doubt that any one would track this car for more than a few laps. Here's the journey to shaping her up!
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
__________________
PCA National Instructor
TPC Racing stats:
2023 Porsche Sprint Challenge 992 Cup Am Champion
2023 Porsche Sprint Challenge GT4 Pro-Am Team Champion
2022 Porsche Sprint Challenge 992 Cup & 991 Cup Champion
2020 IMSA GT3 Cup Challenge 2nd Championship
2018 IMSA GT3 Cup Challenge 2nd Championship
2016 IMSA GT3 Cup Challenge Champion
2013 IMSA GT3 Cup Challenge Champion
2006 Rolex-24 @ Daytona GT Champion
2004 Grand-Am SGS Class Champion
PCA National Instructor
TPC Racing stats:
2023 Porsche Sprint Challenge 992 Cup Am Champion
2023 Porsche Sprint Challenge GT4 Pro-Am Team Champion
2022 Porsche Sprint Challenge 992 Cup & 991 Cup Champion
2020 IMSA GT3 Cup Challenge 2nd Championship
2018 IMSA GT3 Cup Challenge 2nd Championship
2016 IMSA GT3 Cup Challenge Champion
2013 IMSA GT3 Cup Challenge Champion
2006 Rolex-24 @ Daytona GT Champion
2004 Grand-Am SGS Class Champion
Last edited by Tom@TPC Racing; 08-08-2018 at 09:59 AM. Reason: Revised the title of this thread appropriately. 08-08-2018
The following 2 users liked this post by Tom@TPC Racing:
paddlefoot64 (06-06-2020),
Robocop305 (07-24-2022)
#2
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
The very next day after driving the car home I had to put it on the dyno because it felt pretty flat. It does have an aftermarket cone air filter, which is not my preference. Sure enough power is a little down. And looks like its never had spark plugs and fuel filter change so let's do it!
The following users liked this post:
Robocop305 (11-08-2023)
#3
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I really wish this car came with the factory airbox because it cost about $800!! Need to figure something out with the airbox... and it needs a MAF sensor because it was coated with the cone filter oil.
#5
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
If I am to spend 800 bucks on an airbox, it ain't going to be the stock one! The pictures are worth a thousand words.
#6
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
All that work was worth it. Check out the dyno! All dyno runs made will lid closed.
Trending Topics
#8
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
As I said before, the previous owner spend good money on mods but the results were less than ideal. Just look at this set up... Not one corner was right. I was actually amazing that the steering wheel was even remotely straight! Got some sorting out to do. I only work on my car after shop hours and weekends in case you were wondering.
#11
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
As I swap out the suspension parts, I Cleaned, I Cleaned, and I Cleaned. It take not time to change parts but it take hours and hours to clean. I used up 2 cases of gum cutter and a gallon of simple green.
The following users liked this post:
Robocop305 (07-24-2022)
#14
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
There's more than one way to setup a car. It is my preference to setup the front geometry so that I don't have to run a stiffer rear sway bar for push, which this car had. Not only did I got rid for the GT2 rear bar for the stock .1GT3 rear bar, I also added a stiffer front bar for more rear grip. I don't have money to change shocks & springs now so the best I can do is put on .2 front springs that are laying around.
I want to take the opportunity to give Michael Levitas, owner of TPC Racing a big shout out. Thank You Very Much, Mike, for letting me use the shop after hours and for taking me along to the races to sponge up the setup knowledge from the pro drivers.
I want to take the opportunity to give Michael Levitas, owner of TPC Racing a big shout out. Thank You Very Much, Mike, for letting me use the shop after hours and for taking me along to the races to sponge up the setup knowledge from the pro drivers.
The following 2 users liked this post by Tom@TPC Racing:
koja997 (10-03-2019),
paddlefoot64 (06-06-2020)
#15
Premium Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
...for now.
The previous owner bought genuine Porsche RS rear wheels. Which looks neat...BUT NOT TRACKABLE ON A NARROW BODY!!!
Had to buy a new set of wheel.
Bump tested and corner balanced. Finally, ready for the track.
The previous owner bought genuine Porsche RS rear wheels. Which looks neat...BUT NOT TRACKABLE ON A NARROW BODY!!!
![banghead](https://rennlist.com/forums/graemlins/banghead.gif)
Bump tested and corner balanced. Finally, ready for the track.
![Cheers](https://rennlist.com/forums/images/smilies/beerchug.gif)
The following users liked this post:
cbracerx (05-26-2021)