Sun Visors - How to remove
#16
Intermediate
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
As nfldcoffee described above - make sure to fully coat BOTH the target surface area and the sticker.
An additional suggestion would be to add just a bit of window cleaner or mild soap to the water to break up the water's surface tension, allowing it to sheet better and coat more evenly with less water. This solution will also provide even more 'slipperiness' to the textured plastic surface, allowing you to move the sticker around very easily. It may sound like this would ruin the adhesive on the stickers, but when it dries, the adhesive will be just as permanent as ever.
You can apply this solution either via sprayer as described above, or just swab it on with a very saturated sponge if you're afraid of getting overspray on your interior leather.
Once you get the stickers in place, you can then gently squeegee out the water and any bubbles that were left behind using the edge of a credit card or small body filler spatula. Just make sure the card edge is very smooth and even, or it could scratch your stickers or visor surface.
Hope that helps... I'm considering these 'Cover-up' stickers for the visors in my '07 C2S, so please post some pics of your completed installation.
![thumbup](https://rennlist.com/forums/graemlins/thumbup.gif)
#17
Instructor
Join Date: Apr 2004
Location: Los Angeles, CA
Posts: 112
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I also ordered and received the e-bay cover cup decals today (for both sides of each flap). I went down to my office parking garage during lunch and applied them (was even in a not so well lit area) -- its actually easier than I expected and took me a total of 15 minutes. I did not remove either flap -- no need. I did have to reapply one of the mirror covers slightly, but only because I'm ****. If you do mess up, you will discover the decals aren't as delicate as the instructions lead you to believe -- just pull and re-apply and you'll be good. They look great BTW and am glad I got them.
#18
Three Wheelin'
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Ok I did both sides of my visors last evening, 20 minute job tops.
The visors pulled out and off their stalks with a firm tug.
Next up I placed enough paper towel to cover the decal on the non lighted side and doused with "Goof-Off" Let it sit for 30 seconds and the decals literally wiped off, that easy! A few rubs and all residue was gone. The visor looks a bit wavy at this stage, don't panic.
Next up I applied the eBay cover ups to the lighted side - easy, just follow the sellers instructions, clean, spray and stick, 1, 2, 3.
Then I applied some vinyl detailing product mainly to remove that "Goof-Off" smell.
I then pushed the visors back onto their stalks and was careful not to poke my eye out when climbing back into the car.
By the morning the wavy-ness of the visors was gone and the vinyl was taut.
Visors look great.
The visors pulled out and off their stalks with a firm tug.
Next up I placed enough paper towel to cover the decal on the non lighted side and doused with "Goof-Off" Let it sit for 30 seconds and the decals literally wiped off, that easy! A few rubs and all residue was gone. The visor looks a bit wavy at this stage, don't panic.
Next up I applied the eBay cover ups to the lighted side - easy, just follow the sellers instructions, clean, spray and stick, 1, 2, 3.
Then I applied some vinyl detailing product mainly to remove that "Goof-Off" smell.
I then pushed the visors back onto their stalks and was careful not to poke my eye out when climbing back into the car.
By the morning the wavy-ness of the visors was gone and the vinyl was taut.
Visors look great.
#19
Drifting
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
OK, for those of you who don't want to pull of the visors from the rods, here are some photos illustrating the method described by stevepow. First wedge a thin trim tool between the cover plate and the visor mount. Pry gently and this cover plate will pop off and slide down the rod out of the way. It's held in place by four clips. This exposes the torx-25 screw which you then remove.
A slot in the mount allows access to a bendable clip which you depress with a flat blade screwdriver. With this depressed, pull the side of the mount closest to the window towards you. This rotates the mount about the fixed clip opposite the one you depressed. The visors are now free to mod as you wish.
In my case, I bought leather visors without the stickers along with the leather dome lamp cover. If I ever sell the car, the original parts can be reinstalled.
A slot in the mount allows access to a bendable clip which you depress with a flat blade screwdriver. With this depressed, pull the side of the mount closest to the window towards you. This rotates the mount about the fixed clip opposite the one you depressed. The visors are now free to mod as you wish.
In my case, I bought leather visors without the stickers along with the leather dome lamp cover. If I ever sell the car, the original parts can be reinstalled.
#23
Drifting
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Not that hard, but took a bit longer than the sunvisors. The homelink buttons pop out easily, but the sun roof button took a bit of work to remove from the old assembly without breaking the tabs holding it in place. The dome lamp assembly is easy to remove once you have the dome cover loose and can access the retention clips from the backside. The dome cover is held in place with 2 torx screws under the homelink buttons, plus four tabs (two at the front and two at the side. See photos below for the locations.
#24
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Thanks for the detailed illustration. That'll come in handy when I do mine. The leather bits make quite a difference to the interior look and feel.
Last edited by Ucube; 11-30-2009 at 11:33 AM.
#25
Three Wheelin'
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Excuse the iPhone picture quality.
#28
Three Wheelin'
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Ahhhh - the leather looks great. That's the way to go. Do both mirrors have the vanity lights? The description on Suncoast site makes it sound like it may only be one.
#30
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I made a few set of the covers a couple years ago.
Put them back up on ebay if anyone is interested.
http://cgi.ebay.com/ebaymotors/ws/eB...%3AMESELX%3AIT
Put them back up on ebay if anyone is interested.
http://cgi.ebay.com/ebaymotors/ws/eB...%3AMESELX%3AIT