996 Turbo Picture Thread
07-09-2019, 10:47 AM
#992
RL Community Team
Rennlist Member
Rennlist Member
Pretty.
The following users liked this post:
MotoJB (07-10-2019)
07-09-2019, 04:46 PM
#994
Rennlist Member
Beautiful car, enjoy!
The following users liked this post:
Oak (07-09-2019)
07-10-2019, 06:46 PM
#997
Rennlist Member
07-10-2019, 07:12 PM
#998
Three Wheelin'
@Oak , is that just a piece of yellow laminex on the headlights? Have any more pictures of that?
this pic is of the first attempt which was ok, I initially used some jdm yellow tint which was too light to my liking so I subsequently found the laminex film which was slightly thicker and has a darker yellow tint. I used plastic tape to make a reverse template directly off the headlight by placing the tape around the fog light area and placing a piece of paper and using a lead pencil to ghost trace the raised area of the plastic tape. (note on using the plastic tape: I had to use a succsesive straight pieces around the slightly raised fog light area. wasn't able to simply use one piece aroung the raised area.) Tip: I had to trim the yellow film apporx 1/4" wider than the template to prevent white light bleed around the perimeter. Ideal to find someone that has a cnc die cut that can vector a template and die cut them... let's see some fried eggs sunny side up!
07-10-2019, 07:29 PM
#999
Rennlist Member
pfbz, yes yellow laminex film from amazon https://www.amazon.com/Lamin-x-1-612...JY3PCQW5YJ3MDE.
this pic is of the first attempt which was ok, I initially used some jdm yellow tint which was too light to my liking so I subsequently found the laminex film which was slightly thicker and has a darker yellow tint. I used plastic tape to make a reverse template directly off the headlight by placing the tape around the fog light area and placing a piece of paper and using a lead pencil to ghost trace the raised area of the plastic tape. (note on using the plastic tape: I had to use a succsesive straight pieces around the slightly raised fog light area. wasn't able to simply use one piece aroung the raised area.) Tip: I had to trim the yellow film apporx 1/4" wider than the template to prevent white light bleed around the perimeter. Ideal to find someone that has a cnc die cut that can vector a template and die cut them... let's see some fried eggs sunny side up!
this pic is of the first attempt which was ok, I initially used some jdm yellow tint which was too light to my liking so I subsequently found the laminex film which was slightly thicker and has a darker yellow tint. I used plastic tape to make a reverse template directly off the headlight by placing the tape around the fog light area and placing a piece of paper and using a lead pencil to ghost trace the raised area of the plastic tape. (note on using the plastic tape: I had to use a succsesive straight pieces around the slightly raised fog light area. wasn't able to simply use one piece aroung the raised area.) Tip: I had to trim the yellow film apporx 1/4" wider than the template to prevent white light bleed around the perimeter. Ideal to find someone that has a cnc die cut that can vector a template and die cut them... let's see some fried eggs sunny side up!
07-10-2019, 07:34 PM
#1000
Three Wheelin'
07-10-2019, 11:12 PM
#1001
Rennlist Member
07-10-2019, 11:16 PM
#1002
Three Wheelin'
07-11-2019, 09:58 AM
#1003
RL Community Team
Rennlist Member
Rennlist Member
I was going to suggest if you could figure out a cheap way to mass produce you probably sell quite few of them. Easy to ship too, just put them in an envelope.
07-14-2019, 11:44 AM
#1004
Pro
Car shows everywhere!
This is a real low miler for me!
