My new '99 C2 Coupe Track Car
#211
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
- LWFW (don't tell Jake)
- Headlight Delete
- Grind and cut all extra metal and brackets
- Lexan quarters
- Cup Shifter Cables
- trunk latch pins
- top vent center radiator through bumper
- install brake pressure sensor
- integrate VBox video with AIM system or add an analog module to it to tap existing sensors for RPM, throttle and brake
- lower to 996 cup height
- add shims to LCAs to get to -4.5 camber in the front and -4.0 in the rear
- corner balance
Additional wish list items are:
- move front calipers to rear and install front BBK
- upgrade quiafe LSD to OS Giken
- go back to DMFW and put the FSI engine in this car instead of my daily![nono](https://rennlist.com/forums/graemlins/nono.gif)
But right now I'm just enjoying the crud out of it as is. Back out to Hallet tomorrow thanks to Jason. The group is full but they have the track for 10 hours for 30 people and said I can jump in when people start dropping out. Gotta feed the need.
- Headlight Delete
- Grind and cut all extra metal and brackets
- Lexan quarters
- Cup Shifter Cables
- trunk latch pins
- top vent center radiator through bumper
- install brake pressure sensor
- integrate VBox video with AIM system or add an analog module to it to tap existing sensors for RPM, throttle and brake
- lower to 996 cup height
- add shims to LCAs to get to -4.5 camber in the front and -4.0 in the rear
- corner balance
Additional wish list items are:
- move front calipers to rear and install front BBK
- upgrade quiafe LSD to OS Giken
- go back to DMFW and put the FSI engine in this car instead of my daily
![nono](https://rennlist.com/forums/graemlins/nono.gif)
But right now I'm just enjoying the crud out of it as is. Back out to Hallet tomorrow thanks to Jason. The group is full but they have the track for 10 hours for 30 people and said I can jump in when people start dropping out. Gotta feed the need.
#212
Race Car
Thread Starter
#213
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Just some food for thought, buy perhaps start looking into an electric steering pump? You might be at the point where you'll be getting more weight savings and performance for your dollar. Just a thought - love the progress so far!
#214
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by sweet victory
Just some food for thought, buy perhaps start looking into an electric steering pump? You might be at the point where you'll be getting more weight savings and performance for your dollar. Just a thought - love the progress so far!
#215
Race Director
#216
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Originally Posted by Barn996
That's incredible Slakker! By chance did you weigh your track car on the same scale before you started your Porsche on Jenney Craig?
#217
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Tire wall ripped up the bumper and damaged one of the headlights. The SMART Fast 50 did a good job of getting it back together on the backside and of repairing the broken tabs. I used their plastic repair on the front and then sanded it to get a smooth finish. It came with some really cool mixer nozzles but you have to have all of the surfaces ready to go. Especially with the Fast 50 which I ended up hand mixing most of the time in batches.
![Name: photo705.jpg
Views: 403
Size: 1.04 MB](https://rennlist.com/forums/attachments/996-forum/1105856d1478564971-my-new-99-c2-coupe-track-car-photo705.jpg)
![Name: photo189.jpg
Views: 363
Size: 892.8 KB](https://rennlist.com/forums/attachments/996-forum/1105855d1478564856-my-new-99-c2-coupe-track-car-photo189.jpg)
I used 3M Panel Bond Adhesive to install the headlight caps. I created a channel for it underneath using metal ducting tape. The panel bond is $55 a tube and takes 24 hours to set but it is some awesome stuff.
![Name: photo378.jpg
Views: 411
Size: 959.3 KB](https://rennlist.com/forums/attachments/996-forum/1105853d1478564853-my-new-99-c2-coupe-track-car-photo378.jpg)
![Name: photo582.jpg
Views: 380
Size: 934.2 KB](https://rennlist.com/forums/attachments/996-forum/1105854d1478564855-my-new-99-c2-coupe-track-car-photo582.jpg)
Next up is a corner balance tomorrow and getting the front bumper wrapped on Wed.
![Name: photo705.jpg
Views: 403
Size: 1.04 MB](https://rennlist.com/forums/attachments/996-forum/1105856d1478564971-my-new-99-c2-coupe-track-car-photo705.jpg)
![Name: photo189.jpg
Views: 363
Size: 892.8 KB](https://rennlist.com/forums/attachments/996-forum/1105855d1478564856-my-new-99-c2-coupe-track-car-photo189.jpg)
I used 3M Panel Bond Adhesive to install the headlight caps. I created a channel for it underneath using metal ducting tape. The panel bond is $55 a tube and takes 24 hours to set but it is some awesome stuff.
![Name: photo378.jpg
Views: 411
Size: 959.3 KB](https://rennlist.com/forums/attachments/996-forum/1105853d1478564853-my-new-99-c2-coupe-track-car-photo378.jpg)
![Name: photo582.jpg
Views: 380
Size: 934.2 KB](https://rennlist.com/forums/attachments/996-forum/1105854d1478564855-my-new-99-c2-coupe-track-car-photo582.jpg)
Next up is a corner balance tomorrow and getting the front bumper wrapped on Wed.
#219
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
15lbs with with the headlights and 2lbs with the wiring harnesses.
#220
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
- LWFW (don't tell Jake)
- Headlight Delete
- Grind and cut all extra metal and brackets
- Lexan quarters
- Cup Shifter Cables
- trunk latch pins
- top vent center radiator through bumper
- install brake pressure sensor
- integrate VBox video with AIM system or add an analog module to it to tap existing sensors for RPM, throttle and brake
- lower to 996 cup height
- add shims to LCAs to get to -4.5 camber in the front and -4.0 in the rear
- corner balance
Additional wish list items are:
- move front calipers to rear and install front BBK
- upgrade quiafe LSD to OS Giken
- go back to DMFW and put the FSI engine in this car instead of my daily![nono](https://rennlist.com/forums/graemlins/nono.gif)
But right now I'm just enjoying the crud out of it as is. Back out to Hallet tomorrow thanks to Jason. The group is full but they have the track for 10 hours for 30 people and said I can jump in when people start dropping out. Gotta feed the need.
- Headlight Delete
- Grind and cut all extra metal and brackets
- Lexan quarters
- Cup Shifter Cables
- trunk latch pins
- top vent center radiator through bumper
- install brake pressure sensor
- integrate VBox video with AIM system or add an analog module to it to tap existing sensors for RPM, throttle and brake
- lower to 996 cup height
- add shims to LCAs to get to -4.5 camber in the front and -4.0 in the rear
- corner balance
Additional wish list items are:
- move front calipers to rear and install front BBK
- upgrade quiafe LSD to OS Giken
- go back to DMFW and put the FSI engine in this car instead of my daily
![nono](https://rennlist.com/forums/graemlins/nono.gif)
But right now I'm just enjoying the crud out of it as is. Back out to Hallet tomorrow thanks to Jason. The group is full but they have the track for 10 hours for 30 people and said I can jump in when people start dropping out. Gotta feed the need.
#222
#223
Pro
#224
Race Car
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Ya the GT2 confused me too the first time I saw a 996 cup with a GT2 sticker. I was shocked that they had totally stripped a "GT2" and turned it into a track car. Lol. Maybe I'll get a C2 badge for it.
Next track day is Monday at the Motorsports Ranch 3.1. It's a really fun track with lots of elevation change and forgiving runoffs.
Interesting point on the uprights. Cup car spec is 3.07" front and 3.93" rear. I'm currently at 5" front and 5.25" rear which is how the car came. I definitely think it needs more rake but I don't think dropping 2 more inches in the front will be practical. So I think the answer is somewhere in between. I'll ask Charlie his recommendation since he knows the setup on these cars as well as anyone.
I'm still getting a lot of outside wear on my tires at -3.7F/-3.0R camber I'll probably get more aggressive with it as well.
Next track day is Monday at the Motorsports Ranch 3.1. It's a really fun track with lots of elevation change and forgiving runoffs.
Interesting point on the uprights. Cup car spec is 3.07" front and 3.93" rear. I'm currently at 5" front and 5.25" rear which is how the car came. I definitely think it needs more rake but I don't think dropping 2 more inches in the front will be practical. So I think the answer is somewhere in between. I'll ask Charlie his recommendation since he knows the setup on these cars as well as anyone.
I'm still getting a lot of outside wear on my tires at -3.7F/-3.0R camber I'll probably get more aggressive with it as well.
#225
Former Vendor