Reason for IMS?
#1
Track Day
Thread Starter
Join Date: Sep 2010
Location: Minnesota
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Reason for IMS?
Please excuse the noob question but with all the buzz about the IMSB failures, I began to wonder why Porsche uses an IMS. Why not drive the cams directly from the crank?
#5
Track Day
Thread Starter
Join Date: Sep 2010
Location: Minnesota
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Heathen eh? I can live with that. So the sole purpose of the IMS is to reduce the chain speed and in turn increase chain life? I'm sure sharper minds than mine have long ago figured out that this is the best solution...but I just can't help think that more robust chains and/or more robust oil cooling of the chains would be a simpler, lighter, and possibly even less expensive means of extending chain life.
Thanks for the link...that is a very interesting write-up on the subject.
Thanks for the link...that is a very interesting write-up on the subject.
#6
Banned
Join Date: Jan 2013
Location: Chicagoland Area
Posts: 26,141
Likes: 0
Received 5,416 Likes
on
2,519 Posts
The accountants were calling the shots on the 996 not the engineers.
Trending Topics
#8
Former Vendor
The reason for the IMS was to drive the camshafts with a lower drive chain surface speed, and also to drive the oil pump.
The 9a1 DFI engines drive the cams from the crankshaft as the IMS was omitted. Porsche utilized the IMS for almost 60 years for a very, very good reason. Not until they utilized a ball bearing to support the IMS did problems begin to occur.
Yes, my IMS Solution (www.theimssolution.com) backdates the engine and retrofits the M96/M97 with a pressure oil lubricated and supported plain journal bearing. This supports both radial and longitudinal loads.
#9
Instructor
I think the pertinent question isn't why they designed the engine with an IMS, but rather why they chose to have one end of that shaft ride on a sealed ball bearing, not significantly more robust than what you find in a swimming pool pump...
#10
All you noobs need to ask or discuss this in the appropriate thread in the sticky above(The IMS DISCUSSION Thread). There was a reason why it was created and stickied in the first place. Thank you and welcome.
#11
Would have been Nice to see Friday out with a few 'heres my new 911", "why I love my 911", threads not this crap again.
dont know why we all dont go out and beat the crap out of our 911 bodywork with a ball pean hammer, be quicker that the depreciation by a 1,000 IMS threads
dont know why we all dont go out and beat the crap out of our 911 bodywork with a ball pean hammer, be quicker that the depreciation by a 1,000 IMS threads
#12
Track Day
Thread Starter
Join Date: Sep 2010
Location: Minnesota
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
Thank you for the admonishment and I understand the frustration that comes from "noobs asking questions that have been beat to death" problem that happens on these forums. I've read the sticky. I've read many many threads related to the IMS bearing issues. I have no desire to rehash the failures, the rubbish bearings, or any of that. What I'd never been able to find is a discussion for the reason a layshaft/IMS is employed in these engines. That is all I wanted to learn about or discuss; NOT IMS bearing failures of the M96/M97 engines. I'd like very much to one day post "here's my new 911" but in the meantime, I enjoy learning as much about them as I possibly can.
#15
Former Vendor
If having an IMS was a bad thing, Porsche wouldn't have even made it into 1960.