993 C2S Refurbish Journal
#61
Addict
Rennlist Member
Rennlist Member
Join Date: Jul 2003
Location: Agoura Hills (Los Angeles) California
Posts: 5,184
Received 358 Likes
on
212 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
How hard was it to install the Hella de Micro lights into the unit. Any cutting or was it a plug and play?
I found this link with four different Hella de Micro models. Which one did you use? TIA
http://4wheelonline.com/Hella_Micro_...s_Lights.28275
I found this link with four different Hella de Micro models. Which one did you use? TIA
http://4wheelonline.com/Hella_Micro_...s_Lights.28275
#62
Rennlist Member
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
How hard was it to install the Hella de Micro lights into the unit. Any cutting or was it a plug and play?
I found this link with four different Hella de Micro models. Which one did you use? TIA
http://4wheelonline.com/Hella_Micro_...s_Lights.28275
I found this link with four different Hella de Micro models. Which one did you use? TIA
http://4wheelonline.com/Hella_Micro_...s_Lights.28275
I bought the standard DE units off Amazon since most of the extras were not going to be needed. (brackets, switch, wiring, etc.) Then upgraded the bulbs to a true white (PIAA)
There was a fair amount of cutting, molesting, slicing and glue...but did it all with a Dremel and regular attachments. (All in all took about 2 hours after ducts were painted)
Used this link as guidance:
http://www.pcarworkshop.com/index.ph...lla_Fog_Lights
#63
Addict
Rennlist Member
Rennlist Member
Join Date: Jul 2003
Location: Agoura Hills (Los Angeles) California
Posts: 5,184
Received 358 Likes
on
212 Posts
#66
Rennlist Member
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
New information to me....researching now.
Help me understand the reason behind the Tie Rod Pin mod as I fail to have found anything that explans it better than this:
https://rennlist.com/forums/993-foru...hapter-ii.html
Is this modification to eliminate any "slop" in the steering wheel? If so, why would there be so much slop in the first place? (looking at cross/section shown on thread) If setting a bolt in the tie rod ends is needed, would an allignment also be in order to "true" up each side?
Help me understand the reason behind the Tie Rod Pin mod as I fail to have found anything that explans it better than this:
https://rennlist.com/forums/993-foru...hapter-ii.html
Is this modification to eliminate any "slop" in the steering wheel? If so, why would there be so much slop in the first place? (looking at cross/section shown on thread) If setting a bolt in the tie rod ends is needed, would an allignment also be in order to "true" up each side?
Last edited by Resident Sicko; 07-07-2011 at 02:49 PM.
#67
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
[QUOTE=Is this modification to eliminate any "slop" in the steering wheel? If so, why would there be so much slop in the first place? (looking at cross/section shown on thread) If setting a bolt in the tie rod ends is needed, would an allignment also be in order to "true" up each side?[/QUOTE]
Unless there is a problem with your steering rack, yes it takes out slop. Best way to describe it was that the steering feel (when car is moving) is tighter, more feel, more responsive. You move the steering wheel 1mm, the car immediate moves 1mm.
I didn't have to do any trueing up when I pinned the tie rods. When you do the bushings, mark all the bolt locations/settings.
Unless there is a problem with your steering rack, yes it takes out slop. Best way to describe it was that the steering feel (when car is moving) is tighter, more feel, more responsive. You move the steering wheel 1mm, the car immediate moves 1mm.
I didn't have to do any trueing up when I pinned the tie rods. When you do the bushings, mark all the bolt locations/settings.
#73
Rennlist Member
Thread Starter
#74
Rennlist Member
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
New control arms cleaned up and clear coated. Walrod bushings installed. All going in this week with new beefy front sway bar, tie rod roll pins and stiffer motor mounts. Woo Hoo!
![](http://i304.photobucket.com/albums/nn184/TomCatAvaTorin/Porsche%20993%20C2S%20Project/1311199606389.jpg)
![](http://i304.photobucket.com/albums/nn184/TomCatAvaTorin/Porsche%20993%20C2S%20Project/1311199606389.jpg)
![](http://i304.photobucket.com/albums/nn184/TomCatAvaTorin/Porsche%20993%20C2S%20Project/1311535112610.jpg)