GT3 Seats Install - Complete!
#31
Have been reading old threads for GT3 seat installation info - the loss of headroom seems to be a common complaint. Can you guys who have these seats please measure the seat to headliner distance shown in the photos below & post here?
Ideally for 3 scenarios:
1) modified 996 sliders only
2) 996 sliders w/ BK lowering brackets (R-9078 / R-9079 http://www.bkauto.com/porsche/r9079.php)
3) BK floor mounts (R-9082 / R-9083 http://www.bkauto.com/porsche/r9082.php)
'H-point' to headliner - looks further back along roof due to angle of photo, the end of the tape measure is really at the rear / outside corner of the sunroof:
Add 2" for the tape measure case = 36" total.
Thanks!
Ideally for 3 scenarios:
1) modified 996 sliders only
2) 996 sliders w/ BK lowering brackets (R-9078 / R-9079 http://www.bkauto.com/porsche/r9079.php)
3) BK floor mounts (R-9082 / R-9083 http://www.bkauto.com/porsche/r9082.php)
'H-point' to headliner - looks further back along roof due to angle of photo, the end of the tape measure is really at the rear / outside corner of the sunroof:
Add 2" for the tape measure case = 36" total.
Thanks!
#34
#35
Which sliders do you have? Recaro or 996?
Thx!
#37
Drifting
ToSi,
I found the rake of the seat helps as well. I'm on BK sliders on the factory rail positions. Tilting the seat backwards, gave me needed room (an impt ~1/2" or so), but makes it a slightly longer reach to the steering wheel. I'm 6', but beware just using someone's height as we are all different torso lengths. I think your measurement is a decent idea for comparison.
I found the rake of the seat helps as well. I'm on BK sliders on the factory rail positions. Tilting the seat backwards, gave me needed room (an impt ~1/2" or so), but makes it a slightly longer reach to the steering wheel. I'm 6', but beware just using someone's height as we are all different torso lengths. I think your measurement is a decent idea for comparison.
#39
97cm = ~38 1/8" so virtually the same as Nurburger's floor mounts. Interesting.
E9, which BK mounts do you have? The 9079? which front mounting hole are you using?
Nurburger, thanks for the quick reply!
KJR, agree that tilt is critical. Found these photos in another thread (https://rennlist.com/forums/996-gt2-...-r-9079-a.html) comparing the BK mounts to stock & the amount of tilt is huge.
Actually, this is the real reason behind my asking for measurements.. I wonder if folks are misinterpreting the more upright seating position for a loss of headroom when installing these seats. Granted there's bound to be some measurement error but if we add an inch to E9stibi to account for the BK brackets, the OE mounts should put the seat ~1" lower than the base 993.
What am I missing?
E9, which BK mounts do you have? The 9079? which front mounting hole are you using?
Nurburger, thanks for the quick reply!
KJR, agree that tilt is critical. Found these photos in another thread (https://rennlist.com/forums/996-gt2-...-r-9079-a.html) comparing the BK mounts to stock & the amount of tilt is huge.
Actually, this is the real reason behind my asking for measurements.. I wonder if folks are misinterpreting the more upright seating position for a loss of headroom when installing these seats. Granted there's bound to be some measurement error but if we add an inch to E9stibi to account for the BK brackets, the OE mounts should put the seat ~1" lower than the base 993.
What am I missing?
#41
Yes, and I put them in the front top hole to tilt them a little bit for extra room. I am 5' 10" and have plenty of room with helmet and sunroof. If this is not enough, you just take out the cussions for track driving.
#42
Rennlist Member
I just installed these seats in my 993 using the OE mounts. Was also reading about worries on loss of head room etc. I am 5'8" and like an upright driving position. I find with the seats in I am actually lower then I was with the stock nonsport seats. Can measure for you if helpful
bill
bill
97cm = ~38 1/8" so virtually the same as Nurburger's floor mounts. Interesting.
E9, which BK mounts do you have? The 9079? which front mounting hole are you using?
Nurburger, thanks for the quick reply!
KJR, agree that tilt is critical. Found these photos in another thread (https://rennlist.com/forums/996-gt2-...-r-9079-a.html) comparing the BK mounts to stock & the amount of tilt is huge.
Actually, this is the real reason behind my asking for measurements.. I wonder if folks are misinterpreting the more upright seating position for a loss of headroom when installing these seats. Granted there's bound to be some measurement error but if we add an inch to E9stibi to account for the BK brackets, the OE mounts should put the seat ~1" lower than the base 993.
What am I missing?
E9, which BK mounts do you have? The 9079? which front mounting hole are you using?
Nurburger, thanks for the quick reply!
KJR, agree that tilt is critical. Found these photos in another thread (https://rennlist.com/forums/996-gt2-...-r-9079-a.html) comparing the BK mounts to stock & the amount of tilt is huge.
Actually, this is the real reason behind my asking for measurements.. I wonder if folks are misinterpreting the more upright seating position for a loss of headroom when installing these seats. Granted there's bound to be some measurement error but if we add an inch to E9stibi to account for the BK brackets, the OE mounts should put the seat ~1" lower than the base 993.
What am I missing?
#43
I just installed these seats in my 993 using the OE mounts. Was also reading about worries on loss of head room etc. I am 5'8" and like an upright driving position. I find with the seats in I am actually lower then I was with the stock nonsport seats. Can measure for you if helpful
bill
bill
Thanks for confirming the height suspicion - hopefully a measurement will put the issue to rest.
#44
Rennlist Member
yes please - if you don't mind, could you move the seat to approx. the same fore-aft location as mine? Base of backrest roughly inline with the rear most part of the parking brake lever.
Thanks for confirming the height suspicion - hopefully a measurement will put the issue to rest.
Thanks for confirming the height suspicion - hopefully a measurement will put the issue to rest.
PM me your cell phone or email and I can send the pics to you from my cell phone if interested.
That position by the way is with the seats ALL the way back. So you might want to mount them further back on the car's rails so you have enough leg room and easier in/out. I mounted mine to the first hole on the floor rail mounts on the car. You'll see what I mean when you start to mount them - just go back a few holes. Its nice to have some backward room to ease getting in/out of the car.
bill
#45
Drifting
I measured with my GT3 seats in with BK sliders in both rake positions (only the front moves) and with the seat in my close in driving position and slid back (i'm in the front mounting holes so I can still get stuff into the back seat). Since the rake change is only <1" or so at the front this doesn't seem to change the seat bottom level, thus headroom, at the back of the seat (as geometry would imply, thinking about it).
But this is a dead vertical measurement. I feel I get an extra 1/2" or so from the backward rake position, due to the more laid back torso positioning. It's just enough that I (at 6' tall) I clear the ceiling with my size Large Bell BR-1 helmet.
I measure approximately 37.75" dead vertically to the roof in all these configurations. In the more forward seating position, the tape measure hits the sunroof about 1" behind the center crease and in the back position, about 1" in front of the back of the sunroof opening.
Sorry I forgot you were measuring to the back of the sunroof, so my measurements are slightly different....
But this is a dead vertical measurement. I feel I get an extra 1/2" or so from the backward rake position, due to the more laid back torso positioning. It's just enough that I (at 6' tall) I clear the ceiling with my size Large Bell BR-1 helmet.
I measure approximately 37.75" dead vertically to the roof in all these configurations. In the more forward seating position, the tape measure hits the sunroof about 1" behind the center crease and in the back position, about 1" in front of the back of the sunroof opening.
Sorry I forgot you were measuring to the back of the sunroof, so my measurements are slightly different....