NEW GMG Racing Porsche 991 GT3 Sport Headers High Flow Catalytic Converter
#16
#18
The interesting question would be what does a 997.2 RS rated at 450hp Dyno on GMG's Dyno or on the other shops Dyno. The 991GT3 accelerates significantly faster than all the older GT3 and RS's. In the 1/4mile all results have shown 124-126mph. That's a huge jump from every other GT3/RS. To go that fast given the weight it's definitely making more power than 475hp to the crank
#19
437 rwhp at 14% drivetrain loss = 508 hp at the crank.
437 rwhp at 12% drivetrain loss = 496 hp at the crank.
THis motor is rated at 475 crank hp.
----------
Fabryce, asking the question again I'm guessing this is for both the headers and center section. Any dynos on headers alone? Not having gotten my car yet, I'm hesitant to make it any louder cause its a street car.
I'm most interested in the tq gain in the bottom half of the revs. To me this motor makes plenty of juice at the top end to get into a lot of trouble on and off the track, but the low end tq bump looks fabulous.
#20
The dyno sheet they posted is the headers alone.
Huh?
437 rwhp at 14% drivetrain loss = 508 hp at the crank.
437 rwhp at 12% drivetrain loss = 496 hp at the crank.
THis motor is rated at 475 crank hp.
----------
Fabryce, asking the question again I'm guessing this is for both the headers and center section. Any dynos on headers alone? Not having gotten my car yet, I'm hesitant to make it any louder cause its a street car.
I'm most interested in the tq gain in the bottom half of the revs. To me this motor makes plenty of juice at the top end to get into a lot of trouble on and off the track, but the low end tq bump looks fabulous.
437 rwhp at 14% drivetrain loss = 508 hp at the crank.
437 rwhp at 12% drivetrain loss = 496 hp at the crank.
THis motor is rated at 475 crank hp.
----------
Fabryce, asking the question again I'm guessing this is for both the headers and center section. Any dynos on headers alone? Not having gotten my car yet, I'm hesitant to make it any louder cause its a street car.
I'm most interested in the tq gain in the bottom half of the revs. To me this motor makes plenty of juice at the top end to get into a lot of trouble on and off the track, but the low end tq bump looks fabulous.
#21
#22
Porsches have historically had better than average percentages of power to the wheels...at least all my other cars have been this way. +1 on wanting to know what a 997.2 rs dynos on that dyno.
Obviously this is all just curiosity, the gains from the gmg exhaust work make total sense in this scenario.
Obviously this is all just curiosity, the gains from the gmg exhaust work make total sense in this scenario.
#25
Drivetrain losses arent a static figure, but instead change with RPM (inversely).
The stock parts are to pass emissions and be inexpensive (they save money where possible).
The stock parts are to pass emissions and be inexpensive (they save money where possible).
#26
I have a fair bit of experience on this subject. Whilst youd probably see 8-9% drive train loss (TLF - total loss factor) with a GT3 on a hub mounted dyno such as a Dynapac 4000, on a roller based dyno those looses would be more like 12-14%.
There are to many variables between runs, equipments etc to get anything other than a comparative value from these....
There are to many variables between runs, equipments etc to get anything other than a comparative value from these....
#27
Based on the dyno chart, the HP and torque gains from GMG's less restrictive exhaust are impressive. I didn't expect to see any gains below 4000 rpms where the stock exhaust is usually more than sufficient to handle the flow.
I wonder if the car was put on the dyno immediately after changing headers/cats or if the car was driven for an hour and the ECU was given time to re-adjust before going on the dyno.
.
I wonder if the car was put on the dyno immediately after changing headers/cats or if the car was driven for an hour and the ECU was given time to re-adjust before going on the dyno.
.
#28
Thread Starter
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Joined: Dec 2004
Posts: 3,330
Likes: 451
From: So Cal
The headers are 991GT3 specific along with the dyno charts.
The headers do you use a similar design to the race proven 997 design.
Keep in mind dyno test for the 997 are done in 2wd mode on the dyno and the test for the 991 GT3 are done in AWD mode as the car cannot be dyno tested in 2wd mode due to the electronics in the car.
__________________
sales@gmgracing.com
www.gmgracing.com
714.432.1582
facebook l instagram l youtube l twitter
Porsche | Audi | Ferrari | Lamborghini | McLaren
Performance Tuning | Motorsport | Factory Service
Pirelli World Challege Race Team GT/GTA/GTS/TC
Pirelli GT3 Cup Trophy USA
Porsche Motorsport — Audi Sport Customer Racing — Lamborghini Super Trofeo Series
sales@gmgracing.com
www.gmgracing.com
714.432.1582
facebook l instagram l youtube l twitter
Porsche | Audi | Ferrari | Lamborghini | McLaren
Performance Tuning | Motorsport | Factory Service
Pirelli World Challege Race Team GT/GTA/GTS/TC
Pirelli GT3 Cup Trophy USA
Porsche Motorsport — Audi Sport Customer Racing — Lamborghini Super Trofeo Series
#29
Thread Starter
Basic Sponsor
Rennlist
Site Sponsor
Rennlist
Site Sponsor
Joined: Dec 2004
Posts: 3,330
Likes: 451
From: So Cal
Based on the dyno chart, the HP and torque gains from GMG's less restrictive exhaust are impressive. I didn't expect to see any gains below 4000 rpms where the stock exhaust is usually more than sufficient to handle the flow.
I wonder if the car was put on the dyno immediately after changing headers/cats or if the car was driven for an hour and the ECU was given time to re-adjust before going on the dyno.
.
I wonder if the car was put on the dyno immediately after changing headers/cats or if the car was driven for an hour and the ECU was given time to re-adjust before going on the dyno.
.
#30
Can you please elaborate on that? Maybe others get it but I am unclear how are the elctronics different from 997? RWS should be a non issue in a straight line. Also, do you test with traction and stability off? Thanks in advance.