Best strut brace for 964
#31
#32
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Hey Guys, make sure to check out our GT2 Aluminum Strut bar. Its a direct replacement and will work on all 964 and 993 cars, Turbo and non Turbo. Its a replica of the Porsche Motorsport brace, so it fits perfectly. I have heard some people had to open the holes a little to fit on certain cars, but its rare. We have done a few of them here and they bolted up without any problems. I would be glad to do a nice discounted GB on them if anyone is interested.
thanks,
![](http://i188.photobucket.com/albums/z277/FabspeedMSP/993%20Products/GT2EvoStrutBar.jpg)
thanks,
![](http://i188.photobucket.com/albums/z277/FabspeedMSP/993%20Products/GT2EvoStrutBar.jpg)
We have a number of interested parties.
For the sake of clarity can you confirm that :
1) The bar fits stock mountings, no drilling required
2) The bar fits under the OEM carpet
Also .... if we get 10 or more buyers, what price would you offer?
Best,
g -
#34
#38
Addict
Rennlist Member
Rennlist Member
Thread Starter
Join Date: Feb 2004
Location: Buenos Aires, Argentina
Posts: 1,065
Received 0 Likes
on
0 Posts
#39
Rennlist Member
Join Date: Feb 2010
Location: San Francisco, CA
Posts: 431
Likes: 0
Received 0 Likes
on
0 Posts
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Sorry about the derailment, for those of you interested, I did get a go ahead from Rennline on a group buy. 20% off (thats -$59). I'll start a new thread for those interested.
#40
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Bueller?!
Bueller?!
I've asked Alex@Fabspeed to post a reply to some of the questions potential particpants have (see post #33).
Also PM'ed him about this yesterday .... awaiting response ...
Bueller?!
I've asked Alex@Fabspeed to post a reply to some of the questions potential particpants have (see post #33).
Also PM'ed him about this yesterday .... awaiting response ...
![popcorn](https://rennlist.com/forums/images/smilies/popcorn.gif)
#41
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I spoke with Alex at FabSpeed this AM. He's aready to begin proceeding with this this GB if there's any interest for this 2 point brace. My understanding is that: Made in the US. Two nuts need to be removed from each side, then reused to install the brace. Please PM or email Alex to confirm suitability for your application and to get your order in. My order is pending till demand is known. If it's easier to call Alex, his number is 215 646 4945.
Henry - sorry about your thread getting hijacked!
Geordie - thanks for getting this started!
Henry - sorry about your thread getting hijacked!
Geordie - thanks for getting this started!
#43
Burning Brakes
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
If it is a near copy of the factory bar, it will fit under the carpet nicely. I have the factory bar in my car and the factory carpet goes over the bar without any issues. Hope that helps.
#44
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Thanks for the clarification. I'll be placing my order tomorrow.
Question for the experts: Will I need to get the alignment or corner balancing re-done as a result of removing the 2 nuts on each side to install this brace?
Question for the experts: Will I need to get the alignment or corner balancing re-done as a result of removing the 2 nuts on each side to install this brace?
#45
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I'd ignore me though...I'm not even an amature...
![burnout](https://rennlist.com/forums/graemlins/burnout.gif)