Ealokens Porshe 951
01-14-2023, 10:10 AM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
01-17-2023, 08:41 AM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
Wheel alignment today.
Dyno in a week or 2.
The following users liked this post:
01-19-2023, 08:14 AM
Rennlist Member
Join Date: Feb 2006
Location: Australia
Posts: 18,917
Have you torn down and rebuilt and installed that i5 in a couple of weeks??!!??
01-19-2023, 08:40 AM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
Quote:
Originally Posted by
333pg333
Have you torn down and rebuilt and installed that i5 in a couple of weeks??!!??
No, this is with the built m44
01-19-2023, 07:25 PM
Rennlist Member
Join Date: Feb 2006
Location: Australia
Posts: 18,917
Quote:
Originally Posted by
ealoken
No, this is with the built m44
Right...I thought you might have broken a record there!
03-27-2023, 03:33 PM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
The following 4 users liked this post by ealoken:
04-02-2023, 12:03 PM
Race Car
Join Date: May 2013
Location: Calgary, Alberta, Canada
Posts: 4,015
May I aske the diameter of the primary header tubes and and also the displacement of the 5 cyl?
ABSOLUTE DEDICATION TO BAD ASSERY!
04-02-2023, 12:07 PM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
Quote:
Originally Posted by
Noahs944
May I aske the diameter of the primary header tubes and and also the displacement of the 5 cyl?
ABSOLUTE DEDICATION TO BAD ASSERY!
Thanks Mr ☺️ 42mm outer if i remember.
04-20-2023, 06:07 PM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
Testing looks good, Dyno next week.
a blast to drive this old girl again.
The following users liked this post:
04-21-2023, 03:18 PM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
The following users liked this post:
04-21-2023, 04:56 PM
Pro
Join Date: Jul 2017
Location: Arcata, California
Posts: 618
The following users liked this post:
05-07-2023, 06:15 PM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
The following 4 users liked this post by ealoken:
05-07-2023, 11:45 PM
Race Car
Join Date: May 2013
Location: Calgary, Alberta, Canada
Posts: 4,015
Its so nice to see you driving. It has been a long journey. Its the 4 cylinder in the car now, correct?
The following users liked this post:
05-08-2023, 01:06 AM
Three Wheelin'
Thread Starter
Join Date: Aug 2016
Posts: 1,338
Quote:
Originally Posted by
Noahs944
Its so nice to see you driving. It has been a long journey. Its the 4 cylinder in the car now, correct?
Thanks, yes the fully built 4 cylinder is in the car, 07k swap will happend when my new workshop is done, so this will work for two summers ☺️
05-08-2023, 05:52 PM
Banned
Join Date: May 2023
Posts: 4
Likes: 0
Vibromat work looks good.
The following users liked this post: