Where to get the cheapest new LS7 Crate engine from
#17
Three Wheelin'
Join Date: Feb 2007
Location: Norway
Posts: 1,324
Likes: 0
Received 0 Likes
on
0 Posts
HI, the plate needs to be against a 016R bolt pattern, not lsx bolt pattern, and it will be upside down, if not for that a lot of the gt2 tranny holes would align. if you make a plate Ill buy it, good tips on the wrecked gt2s, once I get my computer up properly again ill contact you
writing from small handheld thingy with 8 inch monitor.. arggggg
writing from small handheld thingy with 8 inch monitor.. arggggg
#18
Rennlist Member
You also need to have the tranny modified to run in a 'flipped' position. Otherwise it will be the fastest 951 in the history of the Universe.....in reverse with 6 speeds.
I've already had that done to mine at California Motorsports. They modify the oil cooler too.
...looking at those pics from the wreckers always sends a bit of a shiver up my spine....
I've already had that done to mine at California Motorsports. They modify the oil cooler too.
...looking at those pics from the wreckers always sends a bit of a shiver up my spine....
#19
Rainman
Rennlist Member
Rennlist Member
You also need to have the tranny modified to run in a 'flipped' position. Otherwise it will be the fastest 951 in the history of the Universe.....in reverse with 6 speeds.
I've already had that done to mine at California Motorsports. They modify the oil cooler too.
...looking at those pics from the wreckers always sends a bit of a shiver up my spine....
I've already had that done to mine at California Motorsports. They modify the oil cooler too.
...looking at those pics from the wreckers always sends a bit of a shiver up my spine....
#21
Banned
Thread Starter
Join Date: Apr 2005
Location: Cheshire, England & Trosa, Sweden
Posts: 1,837
Likes: 0
Received 0 Likes
on
0 Posts
Thanks Gent's ... just got of the phone to Beni who didn't know that I had set this thread up so he promises to chirp in shortly
#22
Rennlist Member
I've got more info re this at home if nobody comes back with it Mark.
#27
Rennlist Member
eww this is getting a bit to Ghey in here....
#28
Three Wheelin'
Join Date: Feb 2007
Location: Norway
Posts: 1,324
Likes: 0
Received 0 Likes
on
0 Posts
douglas valley wanted 4250gbp + vat + delivery.. I had an offer for 4000 euros for a 996 turbo unit, so about the same if you swap diff etc. -1000gbp would be much nicer on my budget
with the USD as it was this summer... you could almost get a new one for that. :|
with the USD as it was this summer... you could almost get a new one for that. :|
#29
Banned
Thread Starter
Join Date: Apr 2005
Location: Cheshire, England & Trosa, Sweden
Posts: 1,837
Likes: 0
Received 0 Likes
on
0 Posts
Try these links:
http://www.carsparefinder.co.uk/
http://www.partfinderuk.co.uk/
http://www.breakerlink.com/index.php
When I buy salvage vehicles I use the above to get quotes for parts before I bid on a car at auction so I get an idea of what a completed project will cost. Simply enter the parts your after and emails are distributed to all the registered salvage yards who then contact you back via email or phone and then you simply go with the cheapest
www.s-w-s.co.uk are currently breaking a red 996 GT2 but I have never dealt with them before.
http://www.carsparefinder.co.uk/
http://www.partfinderuk.co.uk/
http://www.breakerlink.com/index.php
When I buy salvage vehicles I use the above to get quotes for parts before I bid on a car at auction so I get an idea of what a completed project will cost. Simply enter the parts your after and emails are distributed to all the registered salvage yards who then contact you back via email or phone and then you simply go with the cheapest
www.s-w-s.co.uk are currently breaking a red 996 GT2 but I have never dealt with them before.