Got my Aluminum Oil Cap from Nicholas
#31
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
For those of you who questioned a possible gas cap design; I'm going to pass on that project. I spoke with the shop I use and there are a couple issues. The design of the gas caps incorporate a locking mechanism (that clicking noise you hear) to prevent the cap from backing off due to road vibrations,etc and over tightening. The cap also provides ventilation for escaping gases.
These two factors will prove too costly in the tooling process to get right. Translation: too expensive in shop hours to get right; thus too expensive per unit to offer for sell. The idea is to provide a few products for us Porsche folks without it costing a weeks worth of wages. If I can't offer something reasonable enough that I would buy it, I'll let someone else give it a shot.
I'm on that fuel rail cover idea though.
Thanks again guys.
These two factors will prove too costly in the tooling process to get right. Translation: too expensive in shop hours to get right; thus too expensive per unit to offer for sell. The idea is to provide a few products for us Porsche folks without it costing a weeks worth of wages. If I can't offer something reasonable enough that I would buy it, I'll let someone else give it a shot.
I'm on that fuel rail cover idea though.
Thanks again guys.
![thumbup](https://rennlist.com/forums/graemlins/thumbup.gif)
#32
Racer
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Got the plastic cover that Peter F was kind enough to point out was missing in my engine bay today.
Did a quick search for engine bay photos in the forum, to get an idea of how it was supposed to be mounted. If the numbers found in that search are anything to go by, it seems that roughly half the 928s are missing this cover...![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
Went to mount it on the car, and lo and behold what I found:
![](http://i9.photobucket.com/albums/a60/erling2792/Porsche%20928/xPICT0057.jpg)
Yup, it's the original cover wedged in below the cables.
Here's the original cover back in place, held by the new plastic bolt I also got:
![](http://i9.photobucket.com/albums/a60/erling2792/Porsche%20928/xPICT0058.jpg)
Cheers,
Erling
Did a quick search for engine bay photos in the forum, to get an idea of how it was supposed to be mounted. If the numbers found in that search are anything to go by, it seems that roughly half the 928s are missing this cover...
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
Went to mount it on the car, and lo and behold what I found:
![](http://i9.photobucket.com/albums/a60/erling2792/Porsche%20928/xPICT0057.jpg)
Yup, it's the original cover wedged in below the cables.
Here's the original cover back in place, held by the new plastic bolt I also got:
![](http://i9.photobucket.com/albums/a60/erling2792/Porsche%20928/xPICT0058.jpg)
Cheers,
Erling
#33
Racer
Thread Starter
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Just home from a 25 km (15mi) winter excercise drive (on dry roads). Couldn't go fast as such, but engine did reach operating temperature, and I got 1 or 2 bwaaaa moments.
Checked the temperature of the oil cap right after parking the car. It was warm. Not even close to being hot, and no problem at all having it in your palm!
Cheers,
Erling
Checked the temperature of the oil cap right after parking the car. It was warm. Not even close to being hot, and no problem at all having it in your palm!
Cheers,
Erling
#34
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Thanks for the update Erling! I didn't think we would have a problem, but I started second guessing myself.
BTW, awesome set-up on your car (judging by the avatar). The wheels, Euro sidemarker light delete, sleek color set against the ideal backdrop.
BTW, awesome set-up on your car (judging by the avatar). The wheels, Euro sidemarker light delete, sleek color set against the ideal backdrop.
#35
Fleet of Foot
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I just got my cap from Nicholas yesterday, very nice. The only change I will probably make to mine is to paint it the same color as the intake plenum on my engine.
To answer Randy V.'s question, yes it does get a bit too hot to handle after a drive on the freeway but not so much so that you could not use a paper towel or shop cloth to touch it and remove it. I'll have it on my car at the Socal karting event if any locals want to see it.
To answer Randy V.'s question, yes it does get a bit too hot to handle after a drive on the freeway but not so much so that you could not use a paper towel or shop cloth to touch it and remove it. I'll have it on my car at the Socal karting event if any locals want to see it.
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#36
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I got mine almost a week ago. But never able to leave well enough alone, deceided to do a little mod. Hope you like it.
![Smilie](https://rennlist.com/forums/images/smilies/smile.gif)
#37
Fleet of Foot
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Nice! I am also thinking about rounding off the edges a bit on mine. I like the polishing, may just have to incorporate that into mine. Where did you get the small crest?
#38
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Very nice detail indeed! I wanted to do something similar, but then I wouldn't be able to offer them for sale with copyright infringement concerns.
I love it, nice job.
I love it, nice job.
#39
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
Where did you get the small crest?
__________________
Bill
__________________
Bill
#41
Addict
Rennlist Member
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
I purchased mine from Nicole, about 6 months ago. It is a little different from Nicolas'.
Last edited by morganabowen; 02-24-2008 at 07:34 PM. Reason: spelling
#42
Rennlist Member
![Default](https://rennlist.com/forums/images/icons/icon1.gif)
After the initial success of my little project, thanks to my Rennlist friends here, I sold out of the initial batch. Many of you who were left without one asked me to make a new batch, so I did.
Because college has me consumed with studies, I've entrusted them to another friend of ours here on Rennlist to sell, Roger Tyson. In my experience he's a super fast shipper and a friendly, easy-going guy to do business with.
Of course, I still welcome any questions or input you may have, so feel free to contact me if you wish.
Because college has me consumed with studies, I've entrusted them to another friend of ours here on Rennlist to sell, Roger Tyson. In my experience he's a super fast shipper and a friendly, easy-going guy to do business with.
Roger Tyson with 928sRus
roger@928sRus.com
(817)430-2688
(817)430-2688
Of course, I still welcome any questions or input you may have, so feel free to contact me if you wish.