What did you buy for your 924/944/968 today?
03-19-2016, 02:52 PM
#17
Three Wheelin'
03-19-2016, 10:19 PM
#18
03-19-2016, 10:28 PM
#19
Rennlist Member
If I had to do that work again (same thing happened to me last year) I'd pull the engine. At least that way, you can do some useful servicing with nothing in the way.
03-20-2016, 06:26 PM
#22
Rennlist Member
Got a new output shaft seal; for my transaxle yesterday. When installing these seals, be certain not to go too far with the insertion on one side..There is no metal lip inside to catch the seal..if you do what I did, it went all the way through the cover and into the pinion area, damaging the seal in the process. I think it's the side opposite the cover plate. I wound up using an old driveline bearing to tap it in with and also used the depth gauge end of a pair of calipers to get it reasonably square to the case. Comments please, if you wish.
Last edited by Tiger03447; 03-20-2016 at 06:26 PM. Reason: left out a word
03-20-2016, 07:14 PM
#23
Rennlist Member
Wiz,
AASE Sales. They have decals for several years but not for 84, so they agreed to make them for me. I figure that they're in the system now and should be available. The guy I dealt with (Tucker) was very accommodating.
AASE Sales. They have decals for several years but not for 84, so they agreed to make them for me. I figure that they're in the system now and should be available. The guy I dealt with (Tucker) was very accommodating.
03-20-2016, 09:15 PM
#24
Three Wheelin'
03-20-2016, 10:42 PM
#25
Rennlist Member
Scroll down to post #66 https://rennlist.com/forums/924-931-...cussion-5.html to see a 3D printed cover. Coming soon to an eBay near you apparently.
03-20-2016, 10:48 PM
#26
Rennlist Member
New-to-me (used) front brake dust covers.
New-to-me (used) air/oil separator.
Strut tower brace (new).
Solid state DME with prime.
Front rotors and pads (new, duh).
New engine compartment fuel lines.
New fuel filter and lines.
New PS reservoir and hose.
All to fit my '87 924s.
New-to-me (used) air/oil separator.
Strut tower brace (new).
Solid state DME with prime.
Front rotors and pads (new, duh).
New engine compartment fuel lines.
New fuel filter and lines.
New PS reservoir and hose.
All to fit my '87 924s.
03-20-2016, 11:02 PM
#28
Rennlist Member
This week:
Lindsey Racing Head
This month(ish):
New coolant tank
Cam gear bolt
New J-Boot
Fuel Filter
Air Filter
Oil Filter
Radiator cap
Oil Fill Cap
1988 10.2:1 CR Pistons
DME Temp sensor (that I can't find ATM)
New Vac lines (silicone, red)
Spray paint for engine
More tools than I care to admit, because I'm getting old and tired of rigging stuff to work instead of just having the right tool.
Homelink auto dimming mirror
Lindsey Racing Head
This month(ish):
New coolant tank
Cam gear bolt
New J-Boot
Fuel Filter
Air Filter
Oil Filter
Radiator cap
Oil Fill Cap
1988 10.2:1 CR Pistons
DME Temp sensor (that I can't find ATM)
New Vac lines (silicone, red)
Spray paint for engine
More tools than I care to admit, because I'm getting old and tired of rigging stuff to work instead of just having the right tool.
Homelink auto dimming mirror
03-21-2016, 03:13 PM
#30
Installed a 140.00 craigslist trans after cleaning it up and replace all 4 shaft seals, going to do the same to the trans I pulled out and set it aside as a spare, so far the CL trans works great!