Seattle Dyno Day Photos
#1
Burning Brakes
Thread Starter
Seattle Dyno Day Photos
The setting...
The players...
The most gorgeous 968 I've ever seen...
A beautiful C2 964 Turbo...
A C2 964 Turbo w/ 313rwhp...
Awesome Boxster S...
Thanks everyone for a great day!!
The players...
The most gorgeous 968 I've ever seen...
A beautiful C2 964 Turbo...
A C2 964 Turbo w/ 313rwhp...
Awesome Boxster S...
Thanks everyone for a great day!!
#2
Race Car
There were a LOT of people and some great cars there! You're right, the 968 looks amazing! Ian I love your 89 Turbo, who else there had that black one? Excellent pics thanks a lot for letting us see them!! [selecting 5 stars for Ian]
#3
Burning Brakes
Thread Starter
Yes, there was a great turnout! Hats off to Skip for organizing the event. He was also generous enough to offer some great door prizes from Paragon Products. One of the other black 951's belongs to the owner of the dyno shop. I believe he's turning it into a track car.
#6
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Join Date: May 2001
Location: Virtually Everywhere...
Posts: 4,820
Likes: 0
Received 5 Likes
on
5 Posts
Here's me [scared as hell!] It took ~7 seconds to get from 6k to 7k RPM's!!!
My thanks to everyone who dyno'd higher than me... let's see... how many is that... oh, EVERYONE!!! Ah well... Not too bad... 143HP and 158TQ to the wheels. Stock numbers are roughly 133HP and 137TQ (89na) and 118HP and 113TQ (83-87na)[using 17.5% drivetrain loss].
Will have a full article and many more pictures up at Tech-Session soon.
I think everyone went home happy with the results, even if only to know what next to work on. The air/fuel metering comparison was a real eye-opener for some
My greatest thanks to all who came out... I think the count was 12 cars on the dyno in 5.5 hours. If you missed brews after at the Redhook, we'll have a go again soon via a dedicated Seattle Beer Night.
[Anyone attending that has pictures, please send them to me or send me the URL of their location and I'll try to get some of them up on the site also.]
Yes, Dyno's are VERY stressful! Especially when your car won't hold an idle after the third run
My thanks to everyone who dyno'd higher than me... let's see... how many is that... oh, EVERYONE!!! Ah well... Not too bad... 143HP and 158TQ to the wheels. Stock numbers are roughly 133HP and 137TQ (89na) and 118HP and 113TQ (83-87na)[using 17.5% drivetrain loss].
Will have a full article and many more pictures up at Tech-Session soon.
I think everyone went home happy with the results, even if only to know what next to work on. The air/fuel metering comparison was a real eye-opener for some
My greatest thanks to all who came out... I think the count was 12 cars on the dyno in 5.5 hours. If you missed brews after at the Redhook, we'll have a go again soon via a dedicated Seattle Beer Night.
[Anyone attending that has pictures, please send them to me or send me the URL of their location and I'll try to get some of them up on the site also.]
Yes, Dyno's are VERY stressful! Especially when your car won't hold an idle after the third run
#7
Burning Brakes
Join Date: Nov 2001
Location: Vancouver BC, Canada
Posts: 970
Likes: 0
Received 0 Likes
on
0 Posts
Hey Skip, I was about to make almost the same type of front chin as you have on your car (although I was planning on making the rivets less conspicuous). Did you make that or did you buy it? If you made it, care to gimme a couple hints?? Thanks. Also, where can I get my hands on a couple of those triangular KONI decals (Porsches have decals, not stickers) I wanted to place a one on each side of the car in a tasteful area, say on the front valencse (a la you) or aft of the front wheel arches. I dunno if it will look too ricy though. TIA.
Trending Topics
#9
Race Director
<ol type="1">[*]147hp * 17.5% = 25.725hp[*]147hp - 25.725hp = 121.275hp[/list=a]
or...
or...
#10
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Matt, email me your address and I'll send you some Koni decals and other assorted Koni goodies.
__________________
Your Porsche Parts Superstore
Parts | Tech-Session | Facebook | Youtube
Jason Burkett
Paragon Products - Porsche Parts & Accessories*- 800.200.9366
Tech Session - Porsche Tech & Info*- 361.289.8834
jason@paragon-products.com
Your Porsche Parts Superstore
Parts | Tech-Session | Facebook | Youtube
Jason Burkett
Paragon Products - Porsche Parts & Accessories*- 800.200.9366
Tech Session - Porsche Tech & Info*- 361.289.8834
jason@paragon-products.com
#11
So Skip, I guess your near 0 restriction exhaust worked out for ya?
I thought you were going to go the Flowmaster route as well?
I am curious as the exhaust goodie selection these days is rather large and my shopping list is still empty!
I thought you were going to go the Flowmaster route as well?
I am curious as the exhaust goodie selection these days is rather large and my shopping list is still empty!
#12
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Join Date: May 2001
Location: Virtually Everywhere...
Posts: 4,820
Likes: 0
Received 5 Likes
on
5 Posts
Yeah, the drivetrain loss is one of the most vague calculations on these cars (except for how long it takes to remove the %^#$@ snap ring ). Everytime I ask, I get "between 15-20%"... though, Danno's right...most folks prefer the 15% figure (maybe we're being ambitious). I just split it down the center... plus, it makes me feel better about the money I've spent on *worthwhile* upgrades
I have aftermarket wheels that weigh 1/2lb more than stock PD's, and Kumho's in 245/45-16... every increase in rotational mass bumps the figure a bit higher... not sure there's a good mathematical way to figure this, because we really don't know the starting figures or rotational masses. Danno, is this in your "great big book of everything"?
Skip
I have aftermarket wheels that weigh 1/2lb more than stock PD's, and Kumho's in 245/45-16... every increase in rotational mass bumps the figure a bit higher... not sure there's a good mathematical way to figure this, because we really don't know the starting figures or rotational masses. Danno, is this in your "great big book of everything"?
Skip
#13
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Join Date: May 2001
Location: Virtually Everywhere...
Posts: 4,820
Likes: 0
Received 5 Likes
on
5 Posts
[quote]Originally posted by PSUice944:
<strong>So Skip, I guess your near 0 restriction exhaust worked out for ya?</strong><hr></blockquote>
I think the others in witness of my "near 0 restriction exhaust" would say it has one drawback. DEAFNESS! WHAT? I SAID... DEAFNESS!!! Yup, it worked out great... much better than expected... and under budget at that. My neighbors, fellow autocrossers, and wife especially appreciate the new tone (very subdued until you go WOT, especially with the cat)
[quote]<strong>I thought you were going to go the Flowmaster route as well? </strong><hr></blockquote>
I was, but got schooled on the na backpressure urban legend. Since this car is being prepared for club race, I need the mid and high RPM power more than the low. Not too sure where the middle is, but I can say that my setup feels strongest above 3k, but lost absolutely nothing below it... probably even gained there. (I'd love so much to see a stock 89 curve... the torque figures I got were more than expected, and never seemed low in the lower RPM's) Is this exhaust the 8v na holy grail? Maybe, I think the only way to be sure would be to use the MSDS and Stahl headers with the same header-back system I have. I can't imagine it'd get much better. My A/F was right on... went a little rich at the end (>6k) but I attribute that to the AFM, Throttle, and Intake restrictions (which I can't do much about for ITS). The important thing was my mixture at max power... and that was great!
[quote]<strong>I am curious as the exhaust goodie selection these days is rather large and my shopping list is still empty!</strong><hr></blockquote>
I'll have the full details up in short time, but the exhaust is as follows:
- Bursch header
- custom 2.5" mid-pipes - one with a Catco Cat, the other with a Dynomax UltraFlo Bullet Muffler
- custom 2.5" cat-back - Dynomax UltraFlo Oval, offset in/center out (brings the input closer to the tranny-side CV, so you can run it real close)
If you haven't seen the Dynomax UltraFlo specs, see their site. They "claim" better flows than any others out there... I find it very believable, and am completely satisfied so far.
Skip
<strong>So Skip, I guess your near 0 restriction exhaust worked out for ya?</strong><hr></blockquote>
I think the others in witness of my "near 0 restriction exhaust" would say it has one drawback. DEAFNESS! WHAT? I SAID... DEAFNESS!!! Yup, it worked out great... much better than expected... and under budget at that. My neighbors, fellow autocrossers, and wife especially appreciate the new tone (very subdued until you go WOT, especially with the cat)
[quote]<strong>I thought you were going to go the Flowmaster route as well? </strong><hr></blockquote>
I was, but got schooled on the na backpressure urban legend. Since this car is being prepared for club race, I need the mid and high RPM power more than the low. Not too sure where the middle is, but I can say that my setup feels strongest above 3k, but lost absolutely nothing below it... probably even gained there. (I'd love so much to see a stock 89 curve... the torque figures I got were more than expected, and never seemed low in the lower RPM's) Is this exhaust the 8v na holy grail? Maybe, I think the only way to be sure would be to use the MSDS and Stahl headers with the same header-back system I have. I can't imagine it'd get much better. My A/F was right on... went a little rich at the end (>6k) but I attribute that to the AFM, Throttle, and Intake restrictions (which I can't do much about for ITS). The important thing was my mixture at max power... and that was great!
[quote]<strong>I am curious as the exhaust goodie selection these days is rather large and my shopping list is still empty!</strong><hr></blockquote>
I'll have the full details up in short time, but the exhaust is as follows:
- Bursch header
- custom 2.5" mid-pipes - one with a Catco Cat, the other with a Dynomax UltraFlo Bullet Muffler
- custom 2.5" cat-back - Dynomax UltraFlo Oval, offset in/center out (brings the input closer to the tranny-side CV, so you can run it real close)
If you haven't seen the Dynomax UltraFlo specs, see their site. They "claim" better flows than any others out there... I find it very believable, and am completely satisfied so far.
Skip
#15
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Join Date: May 2001
Location: Virtually Everywhere...
Posts: 4,820
Likes: 0
Received 5 Likes
on
5 Posts
Boeing Surplus, Renton, WA - 4x8 sheet of 1/8" black ABS - ~$13 ...cut lengthwise to 2.5", use 2 layers, fit to car, drill holes every 5-8", use aluminum or other rust resistant nuts and bolts to secure. I also used rubber washer to allow more flex. I ran with a single layer and it broke too easily... doubled-up I was able to mow a few cones, wife ran into the spare tire, and it's still holding up. If you want something a bit better, Boeing also sells sheets of 3/16" & 1/4" Lexan... for a nominal fee of course.
While you might think it does something useful aerodynamically, it's really there to hold my damaged lower lip together, and keep cones from going under the car. The screws are purposely visible to further identify my "who cares what it looks like" character
Skip
While you might think it does something useful aerodynamically, it's really there to hold my damaged lower lip together, and keep cones from going under the car. The screws are purposely visible to further identify my "who cares what it looks like" character
Skip