Removing tenacious rear main seal?
#1
Archive Gatekeeper
Rennlist Member
Rennlist Member
Thread Starter
Removing tenacious rear main seal?
Feel free to toll your eyes, most people have trouble getting their RMS back in, I can't even get the old one out. I tried prying under the edge of the RMS in the groove at 8 o-clock- no go. Then I gently wedged a 90 degree hook into the side in the groove and tore the rubber coating a little. I recall reading on some BMW site about drilling a hole into the RMS and screwing a screw in a turn or two. I pulled the screw out of the hole. Then I stuck the tip of the 90o hook in the hole, yanked on it, and broke it off, so it's stuck behind the RMS now. So I'm committed to getting this bastard out. And it's now seeping oil down and onto my oil pan. And I'm afraid to jack on it too much for fear of slipping and scratching the crank.
I have the clutch assembly and the TT out, so I have all the room in the world, relatively speaking. I recall seeing a picture of someone's RMS post-removal with strips of rubber still attached, maybe I just need to run a blade around the outer circumference? Is the 'sealing' done entriely around the crank (ie- if I scratch the block where the outer edge of the RMS sits, is that a disaster?) If not, can I either A) hammer the screwdriver under the outer lip in the groove, or B) dremel thru the outer rim of the RMS and break the tension of the ring, a la removing flappy bearings?
My apologies to all the real mechanics who are probably shaking their heads....
Suggestions/tips/hints?
I have the clutch assembly and the TT out, so I have all the room in the world, relatively speaking. I recall seeing a picture of someone's RMS post-removal with strips of rubber still attached, maybe I just need to run a blade around the outer circumference? Is the 'sealing' done entriely around the crank (ie- if I scratch the block where the outer edge of the RMS sits, is that a disaster?) If not, can I either A) hammer the screwdriver under the outer lip in the groove, or B) dremel thru the outer rim of the RMS and break the tension of the ring, a la removing flappy bearings?
My apologies to all the real mechanics who are probably shaking their heads....
Suggestions/tips/hints?
#2
Nordschleife Master
its a pain in the *** in the car.
3 days ago i finally pressed the new seal in, but i havent been bothered to get back under the car and put the flywheel back in cause i am kinda burnt out at the moment
I would suggest the drilling tip, but maybe you need to just try and find something else to use to pry the thing out. I pulled my seal and it was a pain but getting it back in was a bigger PITA,
To install use the old seal, plus the new seal and get longer then stock bolts for the flywheel and use the flywheel and the old seal to press the new one in. When its seated, remove the bolts (3 or 4) remove the old seal thats used as a shim and then fully seat the new seal and reinstall the flywheel using the correct bolts.
3 days ago i finally pressed the new seal in, but i havent been bothered to get back under the car and put the flywheel back in cause i am kinda burnt out at the moment
I would suggest the drilling tip, but maybe you need to just try and find something else to use to pry the thing out. I pulled my seal and it was a pain but getting it back in was a bigger PITA,
To install use the old seal, plus the new seal and get longer then stock bolts for the flywheel and use the flywheel and the old seal to press the new one in. When its seated, remove the bolts (3 or 4) remove the old seal thats used as a shim and then fully seat the new seal and reinstall the flywheel using the correct bolts.
#3
928 Collector
Rennlist Member
Rennlist Member
explosives
Actually I punch a hole and grab with a bent pick of sorts... i heat bent a screwdriver. Be careful, the aluminium there is very soft Rob
Actually I punch a hole and grab with a bent pick of sorts... i heat bent a screwdriver. Be careful, the aluminium there is very soft Rob
#4
Addict
Rennlist Member
Rennlist Member
Just take a big screw driver( long handle) , place it in the groove, smack the end with a hammer a couple of time to get the screw driver in there and pry it out. If you can get a bit of an angle on it to get under it some that would be better, but it should pop out. You just want to disfigure the seal a bit to create a gap around the edge by the groove. It'll come out, just don't ***** around with it. Of course be carefull you don't drive the screw drive into the crank shaft.
#6
Nordschleife Master
take a fairly thin (cant be too thin) flat head screw driver, file or sand all edges/surfaces to remove really abrasive marks, and slide it between the crank and the seal.
Do not put it between the block and the seal.
This will get you under the metal part of it, move the handle of the screwdriver towards the opposite side of the crankshaft.
This will give you leverage and it will come out fairly easily.
Keep in mind it will probably deform the seal slightly on exit which is fine.
Do not put it between the block and the seal.
This will get you under the metal part of it, move the handle of the screwdriver towards the opposite side of the crankshaft.
This will give you leverage and it will come out fairly easily.
Keep in mind it will probably deform the seal slightly on exit which is fine.
Trending Topics
#8
Archive Gatekeeper
Rennlist Member
Rennlist Member
Thread Starter
Well, she's out.
Take THAT, beyotch!
Couple of big hits with the BFH, and the old seal buckled. Took about 60 seconds.
The bad news is that I must have made a little ding on the edge of the crank while pissing with my screw or hook:
It's right on that diagonal surface, it's not on the swept surface of the crank, so am I ok if I just emery paper the edge so it doesn't tear the new seal on its way in?
The RMS did manage to extract a lb o' flesh while I was messing with the hook:
Nice view:
Take THAT, beyotch!
Couple of big hits with the BFH, and the old seal buckled. Took about 60 seconds.
The bad news is that I must have made a little ding on the edge of the crank while pissing with my screw or hook:
It's right on that diagonal surface, it's not on the swept surface of the crank, so am I ok if I just emery paper the edge so it doesn't tear the new seal on its way in?
The RMS did manage to extract a lb o' flesh while I was messing with the hook:
Nice view:
#9
Nordschleife Master
yeah that is a neat view, it took me a minute to figure where the hell that was. Obviously your TT is out.
How did you find rebuilding the TT? Dont you need to make some type of giant press to get those bearings in and out?
How did you find rebuilding the TT? Dont you need to make some type of giant press to get those bearings in and out?
#10
Addict
Rennlist Member
Rennlist Member
Good job...should have waited a little bit to read our advice and you could have saved some trouble. Glad you got it out...didn't ***** it!
Anyway, just tell your friends you got bit by a shark.
Anyway, just tell your friends you got bit by a shark.
#11
Under the Lift
Lifetime Rennlist
Member
Lifetime Rennlist
Member
I used Keith's technique with not so much force as to cause the screwdriver to nick the crank. The seal has a metal core under the rubber, so the goal is to create a small longitudinal dent in seal at the notch area. One or two smacks will do that. Then use the tip of the screwdriver in the notch and lever the seal out with the shaft against the pan edge. It won't move at first, but will begin to work out slowly. The notch was cut ln the block just for this purpose.
Hopefully your nicks are away from the seal area, although it looks close. Dress them using a small emery point/drum and Dremel to make sure the new seal does not catch on them during insertion. Those nicks are deep. I once made some very fine scratches on a motorcycle counter-shaft while extracting the seal and the new seal leaked worse than the old one. It took a lot of work with an emery point to smooth it out and get the new seal not to leak.
Hopefully your nicks are away from the seal area, although it looks close. Dress them using a small emery point/drum and Dremel to make sure the new seal does not catch on them during insertion. Those nicks are deep. I once made some very fine scratches on a motorcycle counter-shaft while extracting the seal and the new seal leaked worse than the old one. It took a lot of work with an emery point to smooth it out and get the new seal not to leak.
Last edited by Bill Ball; 12-29-2007 at 01:36 AM.
#12
Archive Gatekeeper
Rennlist Member
Rennlist Member
Thread Starter
Ryan-
Rebuilding the TT was a snap- 5 easy steps:
1. remove old TT
2. Call Jim
3. Drive to Anaheim
4. Transfer shifter bracket, shifter, and re-align.
5. Install new TT.
Bill:
Dumb question- By 'dress', what would you use to smooth that edge of the crank? I have some 2000 grit sandpaper, but I can't find how that compares to crocus cloth or emery paper. Is that ok?
Rebuilding the TT was a snap- 5 easy steps:
1. remove old TT
2. Call Jim
3. Drive to Anaheim
4. Transfer shifter bracket, shifter, and re-align.
5. Install new TT.
Bill:
Dumb question- By 'dress', what would you use to smooth that edge of the crank? I have some 2000 grit sandpaper, but I can't find how that compares to crocus cloth or emery paper. Is that ok?
#13
Nordschleife Master
well thats the $400 method right?
I figured you would have just bought the 3 bearings for $50 and done it yourself. Perhaps it is too much of a pain to get involved in all that
I figured you would have just bought the 3 bearings for $50 and done it yourself. Perhaps it is too much of a pain to get involved in all that
#14
Under the Lift
Lifetime Rennlist
Member
Lifetime Rennlist
Member
I think emery works best on this metal. Crocus would probably be OK. Just trying to take the edge/burr off. If the nicks are in the sealing area, you've got a problem.
#15
Three Wheelin'
Join Date: Jan 2007
Location: not where you think I am
Posts: 1,466
Likes: 0
Received 0 Likes
on
0 Posts
if there is no seal or bearing riding on the scuffed area of the crank, you could just leave it alone...? other-wise, emory cloth should do......
--Russ
--Russ