What would cause all 4 injectors to dump way too much fuel?
#1
Race Director
Thread Starter
What would cause all 4 injectors to dump way too much fuel?
I reinstalled my computer, replaced the FPR, and replaced the plugs. I'm still dumping waaay too much fuel. From what I understand a bad FPR (too much fuel pressure) would make the injectors stay closed.. anyone know what would make all 4 injectors dump too much fuel?
#7
Race Director
Thread Starter
New temp sensor, didn't touch the chips but I will pull the computer again and double check.
I understand when the FPR fails it usually results in over pressure, but I heard if ithe injectors have too much pressure they won't fire. am I wrong?
I did replace the stock 2.5 fpr (that I think failed) with a new 3bar , but I doubt my chips are tuned for that (europroducts?) I figured I could use the arc-2 to get it in the ballpark until I can get Maxtune. I wonder if thats the problem now..
Dan, thanks for the offer, if I find out I need to use a 2.5 bar fpr for now I'll let you know
thanks!
I understand when the FPR fails it usually results in over pressure, but I heard if ithe injectors have too much pressure they won't fire. am I wrong?
I did replace the stock 2.5 fpr (that I think failed) with a new 3bar , but I doubt my chips are tuned for that (europroducts?) I figured I could use the arc-2 to get it in the ballpark until I can get Maxtune. I wonder if thats the problem now..
Dan, thanks for the offer, if I find out I need to use a 2.5 bar fpr for now I'll let you know
thanks!
Trending Topics
#9
Burning Brakes
Join Date: Jun 2004
Location: new jersey
Posts: 884
Likes: 0
Received 0 Likes
on
0 Posts
i swear your problem is exactly what my car was doing after i installed my vitesse stage 3 kit(which had nothing to do with my problem)john helped me through it and turned out to be one of the computers...my car was sputtering and dumping fuel and smoking very bad....just a thought
#11
Race Director
Thread Starter
i swear your problem is exactly what my car was doing after i installed my vitesse stage 3 kit(which had nothing to do with my problem)john helped me through it and turned out to be one of the computers...my car was sputtering and dumping fuel and smoking very bad....just a thought
When I pulled the rail they all had a consisent spray
thanks guys
mike
#14
Addict
Rennlist Member
Rennlist
Site Sponsor
Rennlist Member
Rennlist
Site Sponsor
Define "Way Too Much Fuel". Using a 3bar FPR with a chip for a 2.5bar FPR will increase fuel delivery by roughly 9%. Are the injectors spraying full blast 100% all of the time, or spraying a bit more than expected causing the car to run rich?
Are you seeing this across the RPM or just idle? At idle, if the vacuum line between regulator and manifold is not connected or is bad, then the car will run pig-rich (it will be lean under boost).
A faulty O2 sensor, giving a constant lean signal will cause the DME to try and richen the mixture.. Unplug the O2 sensor, what happens?
If the injectors are spraying 100% all of the time, you could have a bad DME or a shorted wire to the injectors..
It's a bit too early to start changing parts. Define the problem a bit better, isolate it (idle, PT, WOT) then it will be a bit easier to find the cause.
Are you seeing this across the RPM or just idle? At idle, if the vacuum line between regulator and manifold is not connected or is bad, then the car will run pig-rich (it will be lean under boost).
A faulty O2 sensor, giving a constant lean signal will cause the DME to try and richen the mixture.. Unplug the O2 sensor, what happens?
If the injectors are spraying 100% all of the time, you could have a bad DME or a shorted wire to the injectors..
It's a bit too early to start changing parts. Define the problem a bit better, isolate it (idle, PT, WOT) then it will be a bit easier to find the cause.
#15
Race Director
Thread Starter
Define "Way Too Much Fuel". Using a 3bar FPR with a chip for a 2.5bar FPR will increase fuel delivery by roughly 9%. Are the injectors spraying full blast 100% all of the time, or spraying a bit more than expected causing the car to run rich?
I do remember my injector duty cycle gauge was showing ~10-30% duty cycle at low loads/rpm...When cranking it doesn't show anything. Does that make any sense? I wish I was looking at it when it started to run on 3 cylinders and then die.
Some background:
Last week I went for a drive , the car started running like crap (wouldn't rev, no power, back firing), then started running on 3 cylinders, then died and wouldn't restart. I have spark and my noid light shows proper voltage getting to the injectors.. Each injector has ~4.5ohms
I suspected a bad FPR , replaced the 2.5 bar one with a 3 bar (I will be buying chips to match the 3 bar soon, just figured no point in buying a 2.5 only to replace it after a month) and replaced the plugs. Still no start.
thanks everyone