Rennlist - Porsche Discussion Forums
It is the only bright thing in the entire cockpit. I think I like it.....
It is the only bright thing in the entire cockpit. I think I like it.....
0 2020/06/05 07:15:18
Pushed in.
Pushed in.
0 2020/06/05 07:15:14
0 2020/06/05 07:15:09
When the horn ring 3 prongs are captive inside the housing, looking from the back, rotate the horn button until the 3 prongs like up with the 3 slots in the printed housing = push and it will click into place and now you have a sprung button....
When the horn ring 3 prongs are captive inside the housing, looking from the back, rotate the horn button until the 3 prongs like up with the 3 slots in the printed housing = push and it will click into place and now you have a sprung button....
0 2020/06/05 07:15:05
To install: Tilt the horn button to get 2 of these prongs under the lip of the housing. Then push the 3rd prong towards the centre (bend it) while you push the button into the printed housing. This is so the 3rd prong does not gouge the printed and painted plastic when you engage it into the housing.
To install: Tilt the horn button to get 2 of these prongs under the lip of the housing. Then push the 3rd prong towards the centre (bend it) while you push the button into the printed housing. This is so the 3rd prong does not gouge the printed and painted plastic when you engage it into the housing.
0 2020/06/05 07:15:03
Take the horn button and metal pad disk from the original RS wheel padded section. They just snap out once you press the 3 prongs in from the rear.
Take the horn button and metal pad disk from the original RS wheel padded section. They just snap out once you press the 3 prongs in from the rear.
0 2020/06/05 07:15:02
Install the spring so it contacts the outer spade (it cannot really do anything else, there isn't the room).
Install the spring so it contacts the outer spade (it cannot really do anything else, there isn't the room).
0 2020/06/05 07:15:00
..... bend the bare male spade over on the inside. The spade is now captive and cannot move. Do the same for the other wire/spade. Note the outer spade is bent towards the outside diameter. The inner spade is bent towards the center point.
..... bend the bare male spade over on the inside. The spade is now captive and cannot move. Do the same for the other wire/spade. Note the outer spade is bent towards the outside diameter. The inner spade is bent towards the center point.
0 2020/06/05 07:14:58
Push the bare male spade through the slot to the inside. Hold it tight up against the back of the horn ring plastic while you......
Push the bare male spade through the slot to the inside. Hold it tight up against the back of the horn ring plastic while you......
0 2020/06/05 07:14:57
Bit of heat shrink....
Bit of heat shrink....
0 2020/06/05 07:14:53
Crimp & Solder the bare male spades on both wires.
Crimp & Solder the bare male spades on both wires.
0 2020/06/05 07:14:49
Make two wire tails with (blue) male crimps - these will connect onto the Momo wheel horn wiring. My Momo has black + earth wire so I replicated.... Harvest a couple of male wire spades out of (blue) crimps. Throw away the plastic.
Make two wire tails with (blue) male crimps - these will connect onto the Momo wheel horn wiring. My Momo has black + earth wire so I replicated.... Harvest a couple of male wire spades out of (blue) crimps. Throw away the plastic.
0 2020/06/05 07:14:43
0 2020/06/05 07:14:42
Automotive primer, base (glacier white) and gloss lacquer. It looks grey right?. Then you get it out in the light and it is def sparkling glacier white. I do like this white and all its different shades.
Automotive primer, base (glacier white) and gloss lacquer. It looks grey right?. Then you get it out in the light and it is def sparkling glacier white. I do like this white and all its different shades.
0 2020/06/05 07:14:38
0 2020/06/05 07:00:47
0 2020/06/05 06:59:55
0 2020/06/04 14:35:56
0 2020/06/04 14:35:21
0 2020/06/03 07:19:57
0 2020/06/03 07:13:47
0 2020/06/03 07:13:41
0 2020/06/03 06:51:56
0 2020/06/03 06:51:10
0 2020/06/03 06:51:09
0 2020/06/03 06:51:08
0 2020/06/03 06:51:07
0 2020/06/03 06:51:04
0 2020/06/03 06:51:03
0 2020/06/03 06:51:01
0 2020/06/03 06:50:55
0 2020/05/27 08:37:44
0 2020/05/27 08:35:57
0 2020/05/27 08:33:59
0 2020/05/14 07:35:43
0 2020/05/14 07:35:29
0 2020/05/14 07:35:15
0 2020/05/14 07:35:00
0 2020/05/14 07:34:19
0 2020/05/14 07:33:52
0 2020/05/14 07:33:01